661195
9
Zoom out
Zoom in
Previous page
1/102
Next page
7
Needle and presser foot section
a Needle threader lever
Use the needle threader to thread the needle.
b Buttonhole lever
Lower the buttonhole lever when sewing buttonholes
and bar tacks.
c Presser foot holder
The presser foot is attached to the presser foot holder.
d Presser foot holder screw
Use the presser foot holder screw to hold the presser
foot holder in place.
e Presser foot
The presser foot applies pressure to the fabric during
sewing. Attach the appropriate presser foot for the
selected stitch.
f Needle plate cover
Remove the needle plate cover to clean the bobbin case
and race.
g Feed dogs
The feed dogs feed the fabric.
h Quick-set bobbin
Begin sewing without pulling up the bobbin thread.
i Bobbin cover
Remove the bobbin cover and then insert the bobbin
into the bobbin case.
j Needle plate
The needle plate is marked with guides to help sew
straight seams.
k Needle bar thread guide
Pass the upper thread through the needle bar thread
guide.
l Presser foot lever
Raise and lower this lever to raise and lower the presser
foot.
m Needle clamp screw
Use the needle clamp screw to hold the needle in place.
Operation buttons
The operation buttons help you to easily perform various basic sewing machine operations.
a Start/stop button
Press the start/stop button to start or stop sewing. The
machine sews at a low speed at the beginning of sewing
while the button is continuously pressed. When sewing
is stopped, the needle is lowered into the fabric. For
details, refer to “Starting to sew” (page 40).
b Reverse/reinforcement stitch button
Press the reverse/reinforcement stitch button to sew
reverse stitches or reinforcement stitches. Reverse
stitches are sewn by keeping the button pressed down to
sew in the opposite direction. Reinforcement stitches
are sewn by sewing 3 to 5 stitches on top of each other.
For details, refer to“Securing the stitching” (page 42).
c Needle position button
Press the needle position button to raise or lower the
needle. Pressing the button twice sews one stitch.
d Sewing speed controller
Slide the sewing speed controller to the left or right to
adjust the sewing speed.
Slide the sewing speed controller to the left to reduce
the sewing speed, or slide the speed controller to the
right to increase the sewing speed.
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Baby Lock Grace - BL40A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Baby Lock Grace - BL40A in the language / languages: English as an attachment in your email.

The manual is 2,94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Baby Lock Grace - BL40A

Baby Lock Grace - BL40A Quick start guide - English - 20 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info