661194
12
Zoom out
Zoom in
Previous page
1/150
Next page
NAMES OF MACHINE PARTS AND THEIR FUNCTIONS
11
Operation Buttons
a “Start/Stop” button
When this button is pressed, the machine sews a few stitches at
a low speed, then begins sewing at the speed set by the sewing
speed controller. Press this button again to stop sewing. This
button lights up in a different color depending on the machine’s
operating condition.
b “Reverse/Reinforcement Stitch” button
This button is used to sew reinforcement stitches at the
beginning and end of stitching. When this button is pressed, the
machine sews 3 to 5 stitches in the same spot, then stops
automatically. For straight and zigzag stitches that take reverse
stitches, the machine sews reverse stitches (stitches sewn in
the opposite direction) at low speed only while the “Reverse/
Reinforcement Stitch” button is held down.
c “Needle Position” button
Use this button to change the sewing direction or for detailed
sewing in small areas. Press this button to raise or lower the
needle position. Press this button twice to sew a single stitch.
d “Thread Cutter” button
Press this button after sewing to automatically trim the excess
thread.
e “Presser Foot Lifter” button
Press this button to lower the presser foot and apply pressure to
the fabric. Press this button again to raise the presser foot.
f Sewing speed controller
Slide the sewing speed controller to the left or right to adjust the
sewing speed. Slide the controller to the left to sew at lower
speeds. Slide the controller to the right to sew at higher speeds.
Beginners should sew at a lower speed until they become
familiar with the machine.
Included Accessories
The accessories are stored in the flat bed
attachment. Open the flat bed attachment as
shown below.
a Bobbin stand
(Place the bobbins on the pins to store them.)
b Storage space
c Presser foot storage tray
(Store presser feet marked A, G, I, J, M, N, and R.)
Green: The machine is ready to sew or is sewing.
Red: The machine cannot sew.
CAUTION
Do not press the “Thread Cutter” button after
the threads have already been cut. Otherwise,
the needle may break, the threads may become
tangled, or damage to the machine may occur.
a
b
c
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Baby Lock Espire - BLSR at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Baby Lock Espire - BLSR in the language / languages: English as an attachment in your email.

The manual is 4,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Baby Lock Espire - BLSR

Baby Lock Espire - BLSR Quick start guide - English - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info