661193
171
Zoom out
Zoom in
Previous page
1/189
Next page
TROUBLESHOOTING
170
Needle breaks The needle is installed incorrectly. Reinstall the needle correctly. 34
The needle clamp screw is not tightened. Tighten the needle clamp screw. 35
The needle is bent or blunt. Replace the needle with a new one. 34
The thread or needle is not suitable for the type
of fabric being sewn.
Check the table of fabric, thread and needle
combinations, and select the appropriate
combination.
36
The wrong presser foot was used. Attach the correct presser foot. 179
The upper thread tension is too strong. Adjust the thread tension. 43
The fabric is pulled during sewing. Do not pull the fabric during sewing.
The spool is installed incorrectly. Reinstall the spool correctly. 29
There are scratches around the hole in the
needle plate.
Replace the needle plate, or consult your
authorized retailer.
There are scratches around the hole(s) in the
presser foot.
Replace the presser foot, or consult your
authorized retailer.
There are scratches on the race. Replace the race, or consult your authorized
retailer.
The needle is defective. Replace the needle. 34
Fabric does not feed
through the machine
The feed dogs are lowered. Use the feed dog position switch to raise the feed
dogs.
81
The stitches are too close together. Lengthen the stitch length. 42
The wrong presser foot was used. Attach the correct presser foot. 179
The needle is bent or blunt. Replace the needle with a new one. 34
The thread is tangled. Use scissors, etc., to cut the tangled thread and
remove it from the race, etc.
Machine does not operate There is no pattern selected. Select a pattern. 48, 88, 114, 151
The “Start/Stop” button was not pressed. Press the “Start/Stop” button. 38
The main power switch is not turned on. Turn the main power to on. 16
The presser foot is not lowered. Lower the presser foot. 38
The “Start/Stop” button was pressed while the
foot controller is connected.
Remove the foot controller, or use the foot
controller to operate the machine.
11, 39
The foot controller was pressed to begin
embroidering.
Remove the foot controller and use the “Start/
Stop” button to operate the machine.
11
Embroidery unit does not
operate
There is no pattern selected. Select a pattern. 48, 88, 114, 151
The main power switch is not turned on. Turn the main power to on. 16
The embroidery unit is not attached correctly. Reattach the embroidery unit correctly. 112
The embroidery frame was attached before the
unit was initialized.
Perform the initialization process correctly. 113
LCD cannot be read The LCD contrast is not properly adjusted. Adjust the LCD contrast. 21, 166
Problem Cause Solution Page
CAUTION
This machine is equipped with a thread detection device. If the “Start/Stop” button is pushed before the upper
threading is done, the machine will not operate properly. Also, depending on the pattern selected, the machine may
feed the fabric even if the needle is raised. This is due to the needle bar release mechanism. At these times, the
machine will make a sound different from that made during normal sewing. This is not the sign of a malfunction.
If the power is disconnected during sewing:
Turn the main power to OFF and unplug the machine.
If you restart the machine, follow the instructions for operating the machine correctly.
171


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Baby Lock Esante - BLN at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Baby Lock Esante - BLN in the language / languages: English as an attachment in your email.

The manual is 4,71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Baby Lock Esante - BLN

Baby Lock Esante - BLN Additional guide - English - 7 pages

Baby Lock Esante - BLN Quick start guide - English - 36 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info