661178
13
Zoom out
Zoom in
Previous page
1/16
Next page
7. Maintenance
Changing the Needle(s)
Note: #365A017 needle is a very special needle and is
exclusive for the Embellisher machine. See your Baby
Lock retailer for replacement needles.
Caution: When changing needle(s), unplug the power cord
from the electrical outlet.
1. Open lamp cover and remove finger guard. (see page
4.)
2. Turn the handwheel until the needle bar is at the highest
position and then lower the cloth presser lifter lever.
3. Lower the cloth presser to the lowest position by turning
the cloth presser height adjusting screw clockwise.
4. While holding the needle clamp holder, loosen the nee-
dle clamp fixing screw by turning the large 2mm allen
screwdriver counter-clockwise.
5. Lower the needle clamp holder slowly into the cloth
presser. The needles must not touch the cloth presser.
Tilt the needle clamp holder slightly forward and remove
it from the machine.
6. To remove the individual outer needles, loosen the
needle fixing screw on the needle clamp holder by turn-
ing the small 1.5mm allen screwdriver counter-clock-
wise and remove the needle(s) by using tweezers.
Insert the new needle(s) until the top of the needle
touches the top of the needle hole. Tighten the needle
fixing screw with the small 1.5mm allen screwdriver by
turning the allen screw clockwise. Center needle is
replaced by loosening the center needle fixing screw,
replace needle and then tightening the screw.
Note: #365A017 needles do not have a front or back,
therefore, you can insert the shank of the needle in any
direction.
7. When replacing the needle clamp holder, make sure the
needle bar is in its highest position. Tilt the needle clamp
holder so the needles will slide into the cloth presser
and slide the clamp up onto the needle bar until the red
mark on the needle bar and needle clamp holder align.
Tighten the needle clamp fixing screw by turning with
the large 2mm allen screwdriver clockwise. Adjust the
cloth presser to desired height.
8. Replace finger guard and close lamp cover.
Use #365A017 needles for the Embellisher machine.
Do not use any other type of needles
Allen screwdriver
1.5mm
Needle clamp
fixing screw
Needle fixing
screws
Needle clamp
fixing screw
Red alignment
mark
Needle plate
Allen screwdriver
2mm
10
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Baby Lock Embellisher at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Baby Lock Embellisher in the language / languages: English as an attachment in your email.

The manual is 1,91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info