661185
8
Zoom out
Zoom in
Previous page
1/29
Next page
7
ENGLISH
h
Install the needle plate cover.
For details on installing the needle plate cover,
refer to “Cleaning the Race” in the machine’s
Instruction and Reference Guide.
a Needle plate cover
i
Install the flat bed attachment or embroidery
unit.
j
Insert the thread tail from the spool of thread
through the hole in the bobbin from the inside
to the outside. Hold the thread tail while
winding the thread around the bobbin by
hand. After winding the bobbin so it is filled
as shown below (about 80%), cut the thread.
For precautions on winding the bobbin for
embroidering, refer to step
b of “Selecting the
Pattern” on page 13.
k
Using scissors carefully trim the thread tail as
close to the bobbin as possible.
a Beginning of wound thread
l
Install the bobbin wound with thread.
Whether or not tension should be applied to the
bobbin thread depends on the type of thread
being used.
Note
The bobbin case (gray) cannot be used for sewing in
any way other than bobbin work. After sewing
bobbin work, refer back to the steps in “Preparing
the Bobbin Thread” on page 6 for removing and
cleaning the bobbin case (gray), and then reinstall
the standard bobbin case (black).
CAUTION
Be sure to use the bobbin case (gray) when creating
bobbin work. Using any other bobbin case may
result in the thread becoming tangled or damage to
the machine.
Make sure that the bobbin case is correctly
installed. If the bobbin case is incorrectly installed,
the thread may become tangled or the machine may
be damaged.
CAUTION
When creating bobbin work, use the bobbin cover
with tabs (for bobbin work), otherwise the thread
may become tangled or the needle may break.
CAUTION
Be sure to use the machine’s included bobbin or one
designed specifically for this machine (Class 15).
Using any other bobbin may result in damage or
injuries.
Actual size
This model Other models
Note
Slowly and evenly wind the thread around the
bobbin.
For best results, wind the bobbin so the thread is
snug and not twisted.
CAUTION
If thread extends beyond the top of the bobbin too
much, the thread may become tangled or the
needle may break.
Memo
If inserting thread tail through bobbin hole is difficult
bobbin can be wound by holding tail and wrapping
thread around inside base. Then carefully trim thread
tail so it does not extend from the side of the bobbin.
11.5 mm
(approx.
7/16 inch)
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Baby Lock Ellisimo BLSO at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Baby Lock Ellisimo BLSO in the language / languages: English as an attachment in your email.

The manual is 5,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Baby Lock Ellisimo BLSO

Baby Lock Ellisimo BLSO Additional guide - English - 49 pages

Baby Lock Ellisimo BLSO Additional guide - English - 8 pages

Baby Lock Ellisimo BLSO Quick start guide - English - 76 pages

Baby Lock Ellisimo BLSO User Manual - English - 364 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info