165860
26
Zoom out
Zoom in
Previous page
1/52
Next page
26
AMPLIFICATION MODE SWITCH
(3CH/4CH)
Depending on the selected switch setting the amplifier for channels 3+4
operates in Fullrange or llighpass mode.
POWER LED
Amplifier status-LED - located on the side of the amplifier - signalling nor-
mal operation - when lit green.
PROTECT LED
Lit red when amplifier is in protect mode due to shorted speakers, over-
temperature etc.
FUSE
Fuse for protection of the amplifier-internal electronics against over-load
or faulty operation / wrong manipulation.
+12 V
+ 12 V Power connection terminal to positive terminal of car battery.
REMOTE/REM
Remote switching contact for the automatic (remote) turnon / turn-off of
the power amplifier from the head-unit's remote (or antenna control) lead.
GROUND/GND
Power connection terminal to chassis ground or negative terminal of car
battery (-12 V).
L und R (1CH/2CH)
Speaker output terminals for channels 1+2; i.e. one stereo speaker pair in
fullrange or highpass mode (e.g. subwoofer).
L und R (3CH/4CH)
Speaker output terminals for channels 3+4; i.e. one stereo speaker pair in
fullrange mode or one single speaker connected in lowpass mode
connected in bridged mode (eg. subwoofer).
Minimum impedance by
bridged mode is 4 Ohms!
INPUT L+R (1CH/2CH)
Low-level RCA signal input for connection to head-unit (Front) printout
for a speaker pair that will be either driven in Fullrange or Highpass
amplifier mode.
INPUT L+R (3CH/4CH)
Low-level RCA signal input for connection to head-unit (Rear) pre-out for
a speaker pair or a subwoofer that will be either driven in Fullrange or
Lowpass amplifier mode.
AMPLIFICATION MODE SWITCH
(1CH/2CH)
Depending on the selected switch setting the amplifier for channels 1+2
operates in Fullrange, or Lowpass mode.
INPUT GAIN (1CH/2CH) + (3CH/4CH)
Separate input gain/sensitivity controls for channels 1+2 and 3+4 res-
pectively allowing the matching of the amplifier input section to the
head-unit (pre-out) output voltage.
HIGHPASS FREQ. (1CH/2CH) Crossover filterfrequeney
control for channels 1+2 allowing the setting of the respective highpass
cut-in frequency between 40 and 240 Hz
LOWPASS FREQ. (1CH/2CH)
Crossover filter frequency
control for channels 1+2 allowing the setting of the respective lowpass
cutoff frequency between 50 and 200Hz
LOWPASS FREQ. (3CH/4CH)
Crossover filter frequency
control for channels 3+4 allowing the setting of the respective lowpass
cutoff frequency between 50 and 200Hz
HIGHPASS FREQ. (3CH/4CH) Crossover filterfrequeney
control for channels 3+4 allowing the setting of the respective highpass
cut-in frequency between 40 and 240 Hz
B2
CONNECTIONS AND CONTROLS AXTON C508
4
5
6
7
1
2
3
8
9
10
11
12
13
14
15
16
17
C208 408 508 Manual UK-D-F 23.07.2003 19:30 Uhr Seite 26
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Axton c 508 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Axton c 508 in the language / languages: English, German, French as an attachment in your email.

The manual is 1,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info