167493
39
Zoom out
Zoom in
Previous page
1/60
Next page
39
The "Loudness" function should also be deactivated.
The HIGHPASS filtering setting (HPF) - on the respective (FILTER) FREQ.
control - of the satellite channels will also take away unnecessary mecha-
nical and electrical 'strain' from coaxial speakers or component speaker
systems (compos), as such speakers are not designed to reproduce
powerful bass signals in the first place. Depending on the actual cone
surface area, voice-coil diameter and the rated power handling of the
'satellites' it is recomenended to set the hiphpass cross-over / cut-in
frequency between 40 and 240 Hz.
If the satellite highpass frequency is set too low, the mid-bass repro-
duction will be increased, but at the same time the power-handling
capacity of the satellites will decrease. If the highpass frequency is set
too high, the mid-bass reproduction will become 'thinner' while the
power-handling capacity of the satellites will increase.
As a general guideline, below you find a practice-proven list for appro-
priate satellite (HIGHPASS) FREQ. / HPF crossover frequencies
covering the most widely used dashboard, door and rear-shelf speaker
diameters:
Front Satellite Systems HPF (FILTER) FREQ.
10 cm Ø Coaxials or 2-Way Compos 90-120 Hz
13 cm Ø Coaxials or 2-Way Compos 80-100 Hz
16 cm Ø Coaxials or 2/3-Way Compos 70 - 80 Hz
Heck Satellite Systems HPF (FILTER) FREQ.
10 cm Ø Coaxials or 2-Way Compos 100-150 Hz
13 cm Ø Coaxials or 2-Way Compos 120-130 Hz
16 cm Ø Coaxials or 2/3-Way Compos 100-130 Hz
Satellite rule 1 The better sounding satellite system should
always be installed in the front of the vehicle.
Satellite rule 2 Based on identical speaker diameters and
comparable engineering quality of the front
and rear satellites, the crossover / cut-in
frequency of the front satellites should
usually be set lower than the highpass
frequency of the rear satellites.
The (LOWPASS) FREQ. / LPF crossover frequency for the sub- woofer
should usually be selected between 50 and 90 Hz. Adjust the LOWPASS
FREQ. cut-off control in such a way that the bass reproduction will be
precise and rich, while still delivering a good and solid low-end bass.
Subwoofer Generally, setting the LPF lowpass cut-off
frequency too low will result In a weak and
uncontoured bass response.
Setting the LPF control too high tends to give
the subwoofer a 'booming' sound.
C109-509 Manual DEF.indd 39C109-509 Manual DEF.indd 39 15.02.2005 15:30:34 Uhr15.02.2005 15:30:34 Uhr
39


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Axton c 409 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Axton c 409 in the language / languages: English, German, French as an attachment in your email.

The manual is 1,84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info