167493
33
Zoom out
Zoom in
Previous page
1/60
Next page
33
E
CONNECTING
C109/C209/C409/C509
IMPORTANT: DISCONNECT THE +12V MAIN POWER CABLE
FROM YOUR CAR BATTERY BEFORE ANY CONNECTING WORK
IS CARRIED OUT!
Recommended Power Cable Cross-Sections and Main Fuse
Values (for +12V and Ground cable based on 5m +12 V cable)
Model Cross-Section Main Fuse
C109
20 mm² 60 A
C209
8-20 mm² 30-40 A
C409
20 mm² 60 A
C509
20 mm²
60 A
It is recommended to connect your amplifier in the following
sequence:
1
Make sure your head-unit is turned off and the volume control
is in its minimum position.
2
RCA outputs of your head-unit to respective RCA inputs of your
amplifier (see „Connecting Diagrams“).
Sub pre-outs from head-unit should be fullrange signals because
lowpass pre-out signals always affect the filtering electronics of amp-
lifier! In case of doubt just 'double' a fullrange front or rear pre-out
by using Y-adaptors.
3
Remote lead connection from head-unit to amplifier.
4
Speaker cables to respective speakers or passive crossovers.
Make sure to maintain polarity! "" to "" and "" to "".
For Mono 1-channel mode use of 4/2-channel models, connect the
two terminals "" and "" marked with BRIDGE!
Min. impedance for bridged mode is 4 Ohms!
5
Ground connection to chassis ground or -12 V negative battery pole.
If possible keep ground cable as short as possible and make
sure the chassis contact is well sand-papered, i.e. clean from any
paint, rust or dirt for maximum contact.
6
+12 V power connecteonto positive battery pole. Do not
forget to install a main fuse within 30 cm of car battery (fire
hazard)!!!
Do not connect +12 V cable to battery before re-checking every
other connection on the amplifier!
Turn-on your head-unit keeping your volume at the lowest setting.
The green status LED on front of the amplifier heat sink should light
up now. If not, turn-off your head-unit and re-check all wiring to and
from the amplifier for missing or faulty connections.
C109-509 Manual DEF.indd 33C109-509 Manual DEF.indd 33 15.02.2005 15:30:32 Uhr15.02.2005 15:30:32 Uhr
33


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Axton c 409 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Axton c 409 in the language / languages: English, German, French as an attachment in your email.

The manual is 1,84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info