165857

Axton c 402 Manual

25
Zoom out
Zoom in
Previous page
1/40
Next page
25
REMOTE / REM
Remote switching contact for the automatic (remote) turnon / turn-off
of the power amplifier from the head-unit's remote (or antenna control)
lead.
GROUND / GND
Power connection terminal to chassis ground or negative terminal of car
battery (-12 V).
+12 V
+ 12 V Power connection terminal to positive terminal of car battery.
Fuse
Fuse for protection of the amplifier-internal electronics against over-
load or faulty operation / wrong manipulation.
࿛ L ࿜ und ࿛ R ࿜ (CH3 + CH4)
Speaker output terminals for channels 3+4; i.e. one stereo speaker pair
in fullrange mode or one single speaker connected in lowpass mode
connected in bridged mode (eg. subwoofer).
Minimum impedance by bridged mode is 4 Ohms!
࿛ L ࿜ und ࿛ R ࿜ (CH1 + CH2)
Speaker output terminals for channels 1+2; i.e. one stereo speaker pair
in fullrange or highpass mode (e.g. subwoofer).
POWER LED
Amplifier status-LED - located on the side of the amplifier - signalling
normal operation - when lit green.
PROTECT LED
Lit red when amplifier is in protect mode due to shorted speakers, over-
temperature etc.
+ INPUT L+R (CH1 / CH2)
Low-level RCA signal input for connection to head-unit (Front) print-
out for a speaker pair that will be either driven in Fullrange or
Highpass amplifier mode.
+ INPUT L+R (CH3 / CH4)
Low-level RCA signal input for connection to head-unit (Rear) pre-out
for a speaker pair or a subwoofer that will be either driven in
Fullrange or Lowpass amplifier mode.
+ INPUT GAIN CH1 / CH2 + CH3/ CH4
Separate input gain/sensitivity controls for channels 1+ 2 and 3~4
respectively allowing the matching of the amplifier input section to
the head-unit (pre-out) output voltage.
Amplification Mode Switch FULLRANGE / HIGHPASS
Depending on the selected switch setting the amplifier for channels
1+2 operates in Fullrange or Highpass mode.
Amplification Mode Switch FULLRANGE / LOWPASS
Depending on the selected switch setting the amplifier for channels
3+4 operates in Fullrange or llighpass mode.
HIGHPASS FREQ. CH1/ CH2 + CH3/ CH4
Crossover filterfrequeney controlfor channels 1+2 allowing the setting
of the respective highpass cut-in frequency between 40 and 240 Hz
Note: This control is not active when the amplification mode switch is
in the "Fullrange" position!
LOWPASS FREQ. CH1/CH2 + CH3/ CH4
Crossover filter frequency control for channels 3+4 allowing the set-
ting of the respective lowpass cutoff frequency between 50 and 200Hz
Note: This control is not active when the amplification mode
snitch is in the "Fullrange" position!
B2
CONNECTIONS AND CONTROLS AXTON C502
4a
4b
5a
1a 2a
1b 2b
3a 3b
11
12
10a
10b
9
8
7
6
5b
C202 402 502 (D+E) 30.04.2001 10:14 Uhr Seite 25
… 25 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Axton c 402 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Axton c 402 in the language / languages: English, German as an attachment in your email.

The manual is 1,94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info