Manual Axkid Rekid (page 8 of 67) (English, German, French, Polish, Swedish, Spanish)

768000

Zoom out

Zoom in

1/67

Some vehicles may already be tted with anchorage points at the base of the front seat rails, or, if

installing in the front passenger seat, in front of that seat.

If your vehicle does not have these anchor points, the supplied lower anchor straps must be

used.

For installation in the back seat, feed the buckle end of the anchor strap through either the rear

of the front seat rails, or the hinge of the front seat. The anchoring point needs to be as close

to the oor as possible. In doing so you should always insert the buckle of the anchor strap

through the closest appropriate slot in the strap to create a slip knot then pull tight. This needs to be

repeated on both sides to create two anchor points.

When installing Rekid in the front passenger seat the lower anchor straps must be attached

to the front gliding tracks so the anchor points will be located along the front edge of the

passenger seat.

Pull out the upper tether strap from the belt housing (N) to an appropriate length.

Check that the white marking on the strap (i) is visible. If not, you can try crossing the straps

over (ii) to give them some extra length to enable the white marking to be visible.

Clip the anchor attachments directly onto the vehicle anchorage points (or lower anchor straps

if you have used them). Press down hard on the top of one side (i) of the child restraint then

repeat on the other side (ii). When you do this it’s important that you really use your full body

weight to press down and get the tether straps to really tighten hard. This will give the tether straps

their rst tightening.

Unfold the support leg (R) out to its maximum angle. Pull out the top latch (S) to release the

upper part of the support leg until it reaches the oor. If the support leg does not reach the oor,

repeat with the lower latch (T).

It is important that you check that the support leg is at an angle over 10° from the back of the

seat. You could check this by ensuring that the support leg is further away from the seat than

the vertical line.

Press down on the child restraint from side to side again (i)(ii), the tether straps will be then be

automatically tightened.

If you have installed Rekid in the back seat you can now move the front seat to a comfortable position.

Note: The back of the child restraint may, but does not need to be in contact with the back of the front

seat.

Attaching The Tether Straps

11a

12a

13a

14a

15a

16a

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Axkid Rekid in the language / languages: English, German, French, Polish, Swedish, Spanish as an attachment in your email.

The manual is 1,09 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Axkid Rekid Manual

Product: