765069

Avenli 17805 Manual

5
Zoom out
Zoom in
Previous page
1/24
Next page
98
RP2-20-GB(V1) RP2-20-GB(V1)
It is absolutely essential to select a suitable site for your pool BEFORE attempting to
ll it with any water. Please select a set-up site which strictly conforms to the following
guidelines:
Guide1. Ensure that the area is rm, at (no bumps or mounds of earth) and extremely level, with a grade not exceeding
3° of slope at any point in the set-up area.
Guide2. Make sure that the area you have selected to set-up the pool is completely free of sticks, stones, sharp objects or
other foreign debris.
Guide3. Select an area that is not directly underneath overhead power lines or trees. Additionally, make sure that the pool
set-up area does not contain underground utility pipes, lines, or cables or any kind.
Guide4. If a ground cloth is provided with your pool kit, its use is highly recommended. The ground cloth will help protect
the pool liner from damage due to weed growth, sharp objects, and debris.
Guide5. If at all possible, choose an open location on your property that is exposed to direct sunlight. This will help to
warm your pool.
WARNING:
Pools installed on inadequately level surfaces are subject to leaking,
forming irregularities, or collapse, which can result in property damage or serious in-
jury for those in or around the pool area!
WARNING:
Do not use sand during setup process. If it appears that there is a need
for use of a “leveling agent”, then your set-up site is likely unsuitable. FAILURE TO
OBEY THIS WARNING MAY RESULT IN SERIOUS PERSONAL INJURY.
CAUTION:
Please choose your set-up area carefully, as lawn and other desirable
vegetation underneath the ground cloth(If applicable) will die. Furthermore, try to avoid
setting the ground cloth(If applicable)in areas prone to aggressive plant and weed spe-
cies, as they may grow through the ground cloth(If applicable).
CAUTION:
The pool must be accessible to a 110 or 230-volt AC outlet protected by
a Ground Fault Circuit Interrupter (GFCI). The pool should be set no closer than 2 m. to
the power source, but no further than the length of the lter pump cord. Under no cir-
cumstances should an extension cord be used to extend the range of the connection.
+3°
Bumpy,Sloping Ground-INCORRECT
Flat,Level Ground-CORRECT
PART3-SITE SELECTION
Step4. INSTALL HORIZONTAL BEAM
Step3. INSTALL THE U-TUBES
Slide combined beams into sleeve,the hole on the beams should face outwards.
Slide each U-tube through the bottom addition connected belt T-joint
PART4-SET UP THE POOL
Step1. ACCOUNT FOR ALL PARTS.
Remove all the parts from the carton(s) and place them on the ground in the location where they are to be assembled
Check each part according to “PART REFERENCE” .Make sure all the pieces to be assembled are accounted for.
IMPORTANT: Do not start assembly if any pieces are missing. For replacement pieces call the Consumer Service
telephone number in your area.
The number of persons required for installation: 2 adult at least.
Total installation time except the time for site preparation and water lling :
45 minutes for size 13’ x 6.5’ x 39”/13’ x 6.8’ x 48”
For the steel frame swimming pool, no tools are required for the installation. For the lter pump (if applicable), no tools are
required for the installation.For the ladder (if applicable), the tool required for the installation is one screwdriver, one wrench.
Step2. INSTALL DRAIN VALVES COVER AND STOPPER
Make sure that outer drain plug is inserted into the outer drain cap and drain valve cover is screwed on tightly.Plug the con-
nection holes with the stoppers. (The out drain plug changes according to different size of pool.)
STOPPER Out Drain Plug A Out Drain Plug BDrain Vavle Cover
BEAM E BEAM D BEAM C
For 4m x 2m x 99cm (13’ x 6,5’ x 39”)/4m x 2.07m x 1.22m (13’ x 6,8’ x 48”), the combination is E-D-C
For the short side sleeve of the pool:
For the long side sleeve of the pool:
BEAM A BEAM B
For 4m x 2m x 99cm (13’ x 6,5’ x 39”)/4m x 2.07m x 1.22m (13’ x 6,8’ x 48”), the combination is A-B
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Avenli 17805 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Avenli 17805 in the language / languages: English, German, Dutch as an attachment in your email.

The manual is 2,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info