765041

Avenli 17802 Manual

6
Zoom out
Zoom in
Previous page
1/16
Next page
1110
RF2-20-GB(V1) RF2-20-GB(V1)
4
3
4
1
2
WARNING:
Do not leave pool unattended while lling with water.
WARNING:
If more than 1~2 inches of water collects on any one side before you
start lling in the center.The pool is not level enough, and must be corrected! You
shall pull out the drain plug, release the water completely, disassemble the pool
completely,locate the pool on a plane surface, repeat set up instructiion.
WARNING:
DO NOT OVERFILL as this could cause the pool to collapse.In times of
heavy rainfall you may need to empty some of the water to ensure the level is correct.
PART5-FILL THE POOL WITH WATER
1. Make sure the drain tting is plugged securely and the cap
is in place. Start lling the pool with water. After about 1-inch of
water is on the bottom, stop lling and smooth wrinkles out of the
bottom of the pool. Pull the outer wall out from the top edge, all
around the bottom of the pool, so that it lls evenly.
2. Contineue lling the pool until water level .
Step5. INSTALL T-JOINT(FOR TYPE B)
PART4-SET UP THE POOL
90%
WARNING:
Do not let your children stand at downfold and face the water outlet
during the drainage. The water current may sweep your children.
WARNING:
Pool should be stored at places where is cool and dry, with no sharp
object surroued, or no heavy objects lying above, which may cause damage to the
pool.
PART6-WINTERISING AND LONG-TERM STORAGE
Step1. If you have a lter pump, make sure that the electricity source to the lter pump has been disconnected.
Step2. Check to ensure that the out drain plug is rmly inserted on the inside of the pool.
Step3. Attach your garden hose to the drainage valve connector, and placing the other end of the hose in an area where the
water can drain safely, such as a storm drain or street gutter. Remember that because water always nds its own level, the end
of the hose must be lower in elevation than the pool to ensure complete drainage.
Step4.If you have a lter pump, insert the stopper into the inlet and outlet xtures, on inside of pool, and then disconnect the
lter pump hoses.
Step5. Attach the drainage valve connector to the drain outlet by turning connector in a clockwise direction.
Step6. Open the out drain plug on the inside of the pool and the water will begin to drain immediately.
Step7. Disconnect the hose and drainage valve connector when nished.
Step8. Replace the out drain plug on the inside of the pool.
Step9. Be sure that the pool liner is completely dry before folding the pool for long-term storage. Leaving the pool exposed to
sunlight for a few hours will clean and speed the drying process and make it easier to fold the pool for storage. (Never attempt
to fold or stow a pool that is not completely dry as this could lead to a proliferation of mold or mildew build-up during the time
the pool is in storage.)
Step10. Remember, proper off-season storage is critical to protect your investment in your pool. (espeically in winter)Once
drained and dry, your pool should be carefully folded and wrapped in a ground cloth (if available) or other similar protective
tarp-like material. The pool and all applicable accessories such as the pump, cover, ground cloth, ladder, hoses, clamps, and
hardware should be kept together and stored indoors, in a reasonably warm, dry and weatherproof location.
Before folding, it’s better to dry all parts and pool completely by lying them in the sun
for one hour or so.(PIC.1). And then, spread some talcum powder to prevent the vinyl
from sticking together.
FOLDING INSTRUCTION
Step1. Please fold the protrusion sides inside to gain rectangle shape.(PIC.2).
Step2. Fold each half of the rectangle to gain a smaller rectangle shape.(PIC.3).
Step3. Fold each ends backwards. (PIC.4).
Step4. Fold the rest ends together to create an ultimate rectangle one.(PIC.5).
TIPS1. Please remove air inside to make the folded pool thin and at during each folding.
TIPS2. The original packing can be used for storage.
PIC.1 PIC.3 PIC.4PIC.2
PIC.5
1. Use the connection end of the T-Joint to
connect the adjacent horizontal tubes.
2. Insert the Pin into the hole of connected
horizontal tube and T-Joint rmly.
3. Install the vertical leg cap onto the vertical leg.
4. Insert the vertical leg into the T-Joint through
the belt.
TIP: If you can’t nd the hole on the horizontal
tube or vertical leg please rotate the tubes until
the pin meets the hole.
BELT
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Avenli 17802 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Avenli 17802 in the language / languages: English, French as an attachment in your email.

The manual is 1,89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Avenli 17802

Avenli 17802 User Manual - English, German, Dutch - 24 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info