Manual Avenli 12023 (page 6 of 18) (English, French)

765045

Zoom out

Zoom in

1/18

1110

RF3-20-GB(V1) RF3-20-GB(V1)

It is absolutely essential to select a suitable site for your pool BEFORE attempting to

ll it with any water. Please select a set-up site which strictly conforms to the following

guidelines:

Guide1. Ensure that the area is rm, at (no bumps or mounds of earth) and extremely level, with a grade not exceeding

3° of slope at any point in the set-up area.

Guide2. Make sure that the area you have selected to set-up the pool is completely free of sticks, stones, sharp objects or

other foreign debris.

Guide3. Select an area that is not directly underneath overhead power lines or trees. Additionally, make sure that the pool

set-up area does not contain underground utility pipes, lines, or cables or any kind.

Guide4. If a ground cloth is provided with your pool kit, its use is highly recommended. The ground cloth will help protect

the pool liner from damage due to weed growth, sharp objects, and debris.

Guide5. If at all possible, choose an open location on your property that is exposed to direct sunlight. This will help to

warm your pool.

WARNING:

Pools installed on inadequately level surfaces are subject to leak-

ing, forming irregularities, or collapse, which can result in property damage or

serious injury for those in or around the pool area!

WARNING:

Do not use sand during setup process. If it appears that there is a

need for use of a “leveling agent”, then your set-up site is likely unsuitable. FAIL-

URE TO OBEY THIS WARNING MAY RESULT IN SERIOUS PERSONAL INJURY.

CAUTION:

Please choose your set-up area carefully, as lawn and other desir-

able vegetation underneath the ground cloth(If applicable) will die. Furthermore,

try to avoid setting the ground cloth(If applicable)in areas prone to aggressive

plant and weed species, as they may grow through the ground cloth(If applica-

ble).

CAUTION:

The pool must be accessible to a 110 or 230-volt AC outlet pro-

tected by a Ground Fault Circuit Interrupter (GFCI). The pool should be set no

closer than 2 m. to the power source, but no further than the length of the lter

pump cord. Under no circumstances should an extension cord be used to extend

the range of the connection.

+3°

Bumpy,Sloping Ground-INCORRECT

Flat,Level Ground-CORRECT

PART3-SITE SELECTION PART4-SET UP THE POOL

Step1. ACCOUNT FOR ALL PARTS.

Remove all the parts from the carton(s) and place them on the ground in the location where they are to be assembled

Check each part according to “PART REFERENCE” .Make sure all the pieces to be assembled are accounted for.

IMPORTANT: Do not start assembly if any pieces are missing. For replacement pieces call the Consumer Service

telephone number in your area.

The number of persons required for installation: 2 adult at least.

Total installation time except the time for site preparation and water lling :

30 minutes for size Ф10’×30”/Ф12’×30”

45 minutes for size Ф14’x33”/Ф15’x33”

Step2. INSTALL DRAIN VALVES COVER AND STOPPER

Make sure that outer drain plug is inserted into the outer drain cap and drain valve cover is screwed on tightly.Plug the con-

nection holes with the stoppers. (The out drain plug changes according to different size of pool.)

STOPPER Out Drain Plug A Out Drain Plug BDrain Vavle Cover

Step3. INSTALL HORIZONTAL BEAM

Step4. INSTALL T-JOINT(FOR TYPE B)

1. Use the connection end of the T-Joint to connect

the adjacent horizontal tubes.

2. Insert the Pin into the hole of connected horizon-

tal tube and T-Joint rmly.

3. Install the vertical leg cap onto the vertical leg.

4. Insert the vertical leg into the T-Joint through the

belt.

TIP: If you can’t nd the hole on the horizontal

tube or vertical leg please rotate the tubes until the

pin meets the hole.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Avenli 12023 in the language / languages: English, French as an attachment in your email.

The manual is 2,2 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Avenli 12023

Avenli 12023 User Manual - English, German, Dutch - 27 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Avenli 12023 Manual

Product: