597333
26
Zoom out
Zoom in
Previous page
1/32
Next page
26
the box in which the telephone was packed) on each corner of the
bottom of the telephone housing.
1. Turn the telephone face down on a flat surface.
2. Remove the desktop stand (the upper tabs on the stand are shown as
2 in Figure 6; the lower tabs are shown as 7 in Figure 6). If you are
using a 6416D+M or 6424D+M telephone and want to install the
adjunct module, do so now before proceeding with the following steps.
For more information on the installation of the module, see the
documentation that came in the box with the module.
3. Snap one end of the line cord (D2R or D8W) into the LINE jack (3 in
Figure 6) on the bottom of the telephone.
4. If you are installing a 6416D+ or 6416D+M or a 6424D+ or 6424D+M
with a connected expansion module, snap one end of the expansion
module cord into the XM24 jack (4 in Figure 6).
5. Thread the line cord (and expansion module cord, if appropriate)
through the routing channel leading to the top of the desktop stand
(1 in Figure 6). Make sure that each cord is placed securely under the
square tabs in the routing channel.
6. Snap one end of the coiled handset cord into the Handset jack (6 in
Figure 6). This jack is labeled . Thread the handset cord into the
channel leading to the side edge of the telephone).
7. Turn the telephone right side up, with the front facing you.
8. Snap the free end of the handset cord into the handset and place the
handset in the cradle.
9. If appropriate, snap the free end of the expansion module cord into the
TEL SET jack on the expansion module.
10. Snap the free end of the line cord into the modular wall jack.
11. Lift the handset and listen for dial tone. If there is no dial tone, check all
wire connections to make sure they are secure.
Note: If you are using a headset with the telephone, you can connect it to the
Handset jack (6 in Figure 6) or the Headset jack on some telephones
(5 in Figure 6).
Wall Installation
Note: For wall-mounting, you will need a 1-foot line cord. (This cord is not
supplied with the telephone, but can be ordered by using this
comcode: 103786760.)
If you are wall-mounting the telephone, you should remove the
tray from the base of the telephone. For this purpose, use the
instructions listed under Removing the Telephone Tray later in this
guide.
1. Make sure the 8-conductor wall mount plate is in place.
2. Do the following to reverse the handset hook. (a in Figure 7 shows the
handset retainer located under the handset.)
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Avaya 6416Dplus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Avaya 6416Dplus in the language / languages: English as an attachment in your email.

The manual is 0,53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Avaya 6416Dplus

Avaya 6416Dplus User Manual - German - 62 pages

Avaya 6416Dplus User Manual - Dutch - 62 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info