601694
23
Zoom out
Zoom in
Previous page
1/28
Next page
Maintenance instructions
23
600 Series
DO NOT SPILL FUEL WHEN REFUELING.
SHOULD THIS HAPPEN, WIPE THE FUEL
AWAY IMMEDIATELY IN ORDER TO
AVOID RISK OF FIRE.
ALWAYS STOP THE ENGINE BEFORE
REFUELING.
KEEP THE ENGINE AWAY FROM OPEN
FIRE. DO NOT SMOKE DURING
REFUELING.
14. FUNCTION AND CALIBRATION OF
LOAD SENSOR
The loader is equipped with a load sensor system. It
gives an audible warning signal and at the same time
an indicator lights in the dashboard when tipping
load is being approached. When the system gives a
warning signal the load that is being lifted is too heavy
in relation with the lift capacity of the loader. In this
case one has to either put more counterweights on
the loader or relieve the load that is being lifted.
The load sensor must be calibrated in case one adds
or removes more than two AVANT rear weights (+/-
65 kg) on the machine. Calibrating happens as follows:
1. Mount the amount of rear weights with which you
are going to use the loader.
2. Remove the engine cover plate and the lower left
side rear cover plate.
3. Lift something so heavy with the loader that the
rear wheels lift off the ground.
4. Open the screw pointed by the arrows (see picture)
with two 13 mm keys. As the two steel strips come
in contact, tighten the screw.
5. Lower the rear wheels back to the ground and
mount the cover plates.
6. Check function of the load sensor.
ATTENTION! The rear of the loader can not be
lifted with a jack in order to do the calibration. The
rear wheels must be lifted by using the loader boom
in order that the adjustment can be done correctly.
15. GREASING OF THE MACHINE
Greasing of pivot points is very important in order to
avoid wear. Most of the greasing points are on the
loader boom. There are 16 grease nipples altogether
on a machine with standard boom and 18 grease
nipples on a machine with telescopic boom. The
pictures on page 24 show the location of grease nipples.
16.-29. SERVICE, ENGINE
AVANT 600 series loaders are equipped with a Kubota
diesel engine (see technical specification sheet for the
engine type of each model). Service and maintenance
instructions for the engines can be found in the Kubota
Operators Manual supplied with the loader.
REFUELING
Check fuel level and fill the tank if necessary. Use
diesel fuel only, in accordance with the instructions in
the Kubota engine Operators Manual. Use of other
fuels is not allowed, because their quality and properties
cannot be guaranteed. Make sure not to let the fuel
tank get empty. Should this happen, refuel and restart
- the engine is fitted with automatic fuel bleeding.
FUSE BOX
The fuse box is located on the right
side of the loader boom. Fuses can be
checked by first lifting the boom so
that the fuse box can easily be reached.
The list on the right shows the location
and function of each fuse in the fuse
box.
If the engine does not run and the
boom cannot be lifted, the fuses can
be checked after removing the right
side cover plate.
REMEMBER TO USE THE SERVICE
SUPPORT
WHEN THE LOAD SENSOR STARTS TO
WARN OF EXCESSIVE LOAD: AVOID
ABRUPT MOVEMENTS, STOP LIFTING
OF THE BOOM, RETRACT TELESCOPIC
BOOM AND LOWER THE BOOM SLOWLY.
WHEN THE LOAD SENSOR IS WARNING
DO NOT STEER THE MACHINE BEFORE
THE BOOM IS LOWERED DOWN TO
GROUND LEVEL
NEVER EXTEND THE TELESCOPE WHEN
THE LOAD SENSOR IS WARNING.
23


Need help? Post your question in this forum.

Forumrules
1

Forum

avant-635

Reset search

  • How to reattach side weight to avant ,bolts snapped off. Submitted on 12-1-2022 at 10:46

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Avant 635 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Avant 635 in the language / languages: English as an attachment in your email.

The manual is 1,84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Avant 635

Avant 635 User Manual - Dutch - 36 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info