Manual Autotek TA1400 (page 9 of 32) (English, German, French, Italian, Spanish)

701390

Zoom out

Zoom in

1/32

IMPORTANT NOTES PRIOR TO INSTALLATION

- This device is only suited for a 12 volt system with negative ground.

- Theradiatedheatwhileoperationrequiressufcientaircirculationattheplaceofinstallation.Itis

veryimportantthattheheatsinknsdonothavecontactwithanymetalpartsoranysurfaceswhich

couldimpairaircirculation.Theampliermaynotbeinstalledinsmallclosedlocationorspaces

without air circulation (e.g. spare wheel recess or below the vehicle carpeting). We recommend the

installationinthevehicle’strunk.Ensuresufcientprotectionagainstvibrations,dustanddirt.

- Ensurethattheinputandoutputcablesaresufcientlyseparatedfromthepowersupplycables.

Otherwise interferences may occur.

- Ensure the accessibility of the fuse and the operating elements after installation.

- Thereliabilityandperformanceoftheamplierdependsonthequalityofinstallation.Preferably

consult an expert to install the system, particularly if you want to install several loudspeakers.

POWER SUPPLY AND TURN-ON-CONNECTION

INTERCONNECTION

ATTENTION: Before you start with the installation, disconnect the ground connection from the ve-

hicle’s battery in order to prevent short circuits.

Thepowerwiringwhichisusuallyinstalledinon-boardcarnetworksisnotsufcientforapoweramplier‘s

demands.MakesurethatthepowerwirestoGNDandtothe+12Vterminalhasbeensufcientlyspecied.A

cable cross section of at least 10 mm

mustbeusedtoconnectthebatterytotheamplier‘sterminals.

FirstconnecttheGNDterminaloftheampliertoanappropriategroundconnectionatthechassis.Toensurea

good connection, residue dirt and dust from the connection point. A loose connection may cause malfunctions

or interferences noise and distortion.

Thenconnectthe+12Vterminaloftheamplierwiththebatterybyusinganappropriatecableincludingan

in-line fuse. This fuse should be located very close to the battery; for safety reasons not more than 30 cm

away. Only insert the fuse when the installation, including the connection of the loudspeakers, has been ac-

complished.

Thenconnect the remote turn-on-wire fromthehead unit with the amplier‘sREMterminal.A cable witha

cross-section of 0.5 mm

is adequate.

LOUDSPEAKER CONNECTIONS

- The total impedance must not be lower than 2 ohms.

- Never connect loudspeaker cables with the ground of the chassis or the +12 V supply voltage.

Iftheamplierisoperatedwithatoolowimpedanceorincorrectlyused,theentiresoundsystem

may be damaged. This means a warranty void in such cases.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Autotek TA1400 in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 3,84 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Autotek TA1400 Manual

Product: