Manual Austroflamm Mr. Wu (page 9 of 24) (English, German, French, Italian)

694335

Zoom out

Zoom in

1/24

english 7 Mr. Wu

details please consult your specialist retailer. Make sure that

the combustion air intakes are not blocked!

Stove pipe connection

For your own safety stringent laws apply for connecting the

stove pipes to the chimney. Your professional dealer or

distributor knows these laws. Please have your certified

retailer carry out the connection of your stove.

3. CORRECT OPERATION OF YOUR STOVE

Approved fuels

Cylindrical wood briquettes with a diameter of 8 cm to max.

10 cm. Only use wood briquettes of quality class A1.

Maximum amount of fuel

Maximum amount of fuel to be added: 2 wood briquettes –

max. length 63 cm.

Clean burning

We recommend wood briquettes with a hole; these ignite

well and burn with an appealing flame picture. The burning

of rubbish of any kind is prohibited by the anti-pollution law.

Startup procedures

Insert batteries (6 x AA 1,5 V – see fig. 6) or plug in the

mains adaptor at the rear of the stove (next to the air inlet

nozzle). If both batteries are inserted and the main adaptor

is plugged in, Mr. Wu will automatically use the source of

higher voltage. During the first 3-4 operations – at nominal

heat output – there may be some odour development as the

varnish has not yet hardened.

Making a fire

For the correct and safe operation of your stove please pay

attention of the chimney developing the necessary feed

pressure. This must especially be considered before the

initial operation (or e.g. after the summer heating break) and

during the mid-season heating periods (e.g. at strong wind,

etc.). The air inlet must not be covered or closed. Clean

combustion chamber, empty ash drawer if necessary (watch

out for ambers!).

Please mind that the infeed is on the highest position before

you place the wood briquettes.

Press and hold the arrow key „Up“, to bring the

infeed to the desired position. This can only be

done if the device has not been switched on (LED

above the start button is not on).

Place one wood briquette on the infeed and position it down

with the „Down“ key. As needed you can place a

second wood briquette the same way. The upper

edge of the top briquette should be approx. 6 cm

above the Keramott bottom (see fig. 2). Now split

off a slice of approx. 3 cm with the delivered „Brik-splitter“.

(see fig. 2, 3 and 7). The Brik-splitter fits in any off-the-shelf

electric drill (¼ inch hexagon). Put the ignition aid in the

middle of the briquette and on top again the split slice of the

briquette (see fig. 4).

We recommend two pieces of wood shavings as an ignition

aid.

! !

! Alternatively to the split-off slice and the ignition aid you

can also use the Austroflamm ignition disc.

Fig. 2 and 3: prepare wood briquette

electric drill with Brik-splitter

Fig. 4: placing of ignition aid

Fig. 5: starting position: height – see detail right

Ignite the ignition aids. We recommend a lighter with a long

neck. Close the combustion chamber door slowly.

Move the briquettes including the ignition aids into the

starting position: the upper edge of the briquette slice or the

ignition disc should be 1 cm above the Keramott bottom.

If after approx. 5 min the briquette/ignition disc is well ignited

you can start the automatic mode:

End the stand-by-mode of the control as described before

and press the start key. A LED above the key will flash up in

green shortly after and there will also be an audible signal.

ress any

of the four keys

on th

e controls

once

end the Stand-by-mode.

briquette slice

ignition aid

briquett

second briquette (optional)

Attention: Ignition aids made of gel/paste or in liquid

form are forbidden.

Keramott bottom

6 cm

1 cm

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Austroflamm Mr. Wu in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 7,53 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Austroflamm Mr. Wu Manual

Product: