Manual Austroflamm Ivy (page 8 of 20) (English, German, French, Italian)

694326

Zoom out

Zoom in

1/20

Ivy 6 english

Combustion air

Being the user of the stove you must take care of a

sufficient combustion air supply. Sealed-up windows and

doors may not allow a sufficient combustion air supply or

disturb the draught behaviour of your stove. Please ensure

the additional supply of fresh combustion air if necessary.

For details please consult your specialist retailer. Make sure

that the combustion air intakes are not blocked!

Stove pipe connection

For your own safety stringent laws apply for connecting the

stove pipes to the chimney. Your professional dealer or

distributor knows these laws. Please have your certified

retailer carry out the connection of your stove.

3. CORRECT OPERATION OF YOUR STOVE

Approved fuels

Dry, well cured and natural wood (hardwood preferred),

wood briquettes.

Maximum amount of fuel

Maximum amount of fuel to be added: 1,5 kg wood or 1,3 kg

briquettes. Larger amounts of fuel can lead to overheating

and thus damage the stove.

Clean burning

The wood must be dry (relative wood moisture < 15%) and

untreated and the right amount of wood must be burned in

order to ensure a clean fire that releases only small

amounts of emissions.

Startup procedures

During the first 3-4 operations - at nominal heat output -

there may be some odour development and the varnish has

not yet hardened.

Making a fire

For the correct and safe operation of your stove please pay

attention of the chimney developing the necessary feed

pressure. This must especially be considered before the

initial operation (or e.g. after the summer heating break) and

during the mid-season heating periods (e.g. at strong wind,

etc.).

If there is not enough feed pressure, please light only some

paper or small kindling first, in order to “warm up” the stove

and the chimney.

The air inlet must not be covered or closed.

Clean grate, empty ash drawer if necessary (watch out for

ambers!)!

Position the lever for the combustion air to the open

position (see fig. 2 and 4).

Place 2-3 logs (approx. 1 kg in total) crossways in the

combustion chamber (1) with sufficient distance from each

other (min. 2 cm), on top of that place some softwood

chippings (approx. 0,5 kg) (2) and some ignition aid and

light. (3) (see fig. 3)

Close the door!

We recommend to let the first load burn down without

changing the air lever position.

As soon as no visible flames are left (only embers in the

combustion chamber), you can put another load of logs

(approx. 1,5 kg) in the combustion chamber if desired. (see

fig. 5)

When reloading the stove please repeat the procedure as

mentioned under “first lighting”: air lever top position (=

open), open door carefully, place logs, close door.

Fig. 4: air knob

After a few minutes, when the logs burn well on all sides

(bright, high flames), you can adjust the heat output with the

air lever (lever right = maximum heat output), the flames

should be yellow and never look blueish or have black tips

(otherwise add more air) – see fig. 4. Never close air supply

completely during operation. (danger of flash-fire!)

The stove door may be opened only for refuelling or

disposing of ashes and is to be closed again afterwards.

Figure 5

symbol figures

Figure 3:ignite the

fire

open  closed

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Austroflamm Ivy in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 0,78 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Austroflamm Ivy Manual

Product: