815458
67
Zoom out
Zoom in
Previous page
1/122
Next page
Operating manual Fireplace inserts slied flat + II EN 10 | Connection to ceramic flues
67
10 Connection to ceramic flues
The specifications given in advance in respect of mounting instructions and installation regulations re-
main valid (see distances, thermal insulation, exhaust pipe connection).
The appliances are particularly suitable for installation with ceramic flues. However the faultless work-
ing of the heating system is only guaranteed if the following points are observed:
Calculation of the ceramic flue
Use of suitable Materials
Compliance with maximum lengths of flue
Installation of a direct- or heating flue
Compliance with the necessary free area of the air grilles
The calculation of the ceramic flue must be made in compliance with the specified maximum flue
lengths nd according to the technical rules of the Stove- and Air Heating Constructors Association and
valid designs.
Characteristics for calculating the flue dimensions
Appliance type Exhaust gas mass flow [mg/s] Flue gas temperature at appli-
ance collar [°C]
Req’d Feed pressure at collar
[Pa]
65x S 7.3 / 7.7 / 6.8 283 / 298 / 317 12
75x S 8.1/7.7 313/300 12
75x39 SII 7.3 286 12
75x51 SII 13.07 252 13
80x64 S
80x64 SII
8.28/8.43 312/291 12
97x S 9.9 274/288 12
120x45 S 14.88 254 13
Maximum length of chamotte ceramic flues
The flue gas temperatures at the appliance collar are average temperatures over the duration of the
combustion.
Appliance type Flue length [m] Feed pressure at collar [Pa] Flue gas temperature down-
stream of the flues [ºC]
65x S 4 12 190
75x S 4 12 190
75x39 SII 4 12 190
75x51 SII 4 12 190
80x64 S
80x64 SII
4 12 190
97x S 4 12 190
120x45 S 4 12 190
The flue is constructed of refractory mineral materials. When setting up, attention must be paid to pro-
cessing that is impervious to heating gases. The ceramic flue support must be load-bearing and heat-
resistant. The installation base on which the heat exchanger is to be set up must be heat insulated in
analogy to the manner described in the section on Protection of the set up area.
The flue pipe connection must be connected gas-tight to the ceramic flue by means of plug-in steel
tubes. The connection of the pipes to the ceramic flue is preferably to be made with a premanufac-
tured connection block made of chamotte.
TIP
The steel tube/chamotte transition must be separate (expansion) and tight. The connecting pipes do
not need to be thermally insulated.
67


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Austroflamm Fireplace inserts slied flat II - Kamineinsatz Schieb flach II at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Austroflamm Fireplace inserts slied flat II - Kamineinsatz Schieb flach II in the language / languages: English as an attachment in your email.

The manual is 14.06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Austroflamm Fireplace inserts slied flat II - Kamineinsatz Schieb flach II

Austroflamm Fireplace inserts slied flat II - Kamineinsatz Schieb flach II User Manual - German - 124 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info