800535

Austria Email KRU 052 Manual

18
Zoom out
Zoom in
Previous page
1/72
Next page
18 Id.Nr. 235161-13
The water connection may be made only through an inspected membrane safety valve or membrane safety valve combi-
nation tting (not a piston valve)! A safety valve combination consists of a shut-o, test, non-return, waste and safety valve
with expansion water drain and is installed between the cold water feed line and cold water inlet of the tank in the order
shown:
Tank connection to DIN 1988 and ÖNORM B2531:
Always observe the following:
To ensure proper function of the tting, the latter must be installed only in a frost-protected space. The safety valve runout
must be open and visible and the waste line of the drip catcher (expansion water funnel) must be routed to the waste water
duct so that neither frost nor obstructions caused by dirt and such can cause a problem. Ensure that the drip cup or item to
be drained is free of deposits and soiling.
No shut-o valve or other restriction may be installed between the safety valve and cold water inlet of the water heater.
The safety valve must be set to a response pressure which is less than the rated pressure of the tank.
Before nally connecting the tank, ush the cold water line.
After making the water connection and air-bubble free lling of the tank, check the tting for proper function.
When lifting or turning (venting) the safety valve test button, the water must ow out freely and without backing up through
the expansion water outlet funnel.
The discharge openings of the safety valves (domestic water and heating circuits) must open out into an appropriate drainage
object in order to avoid any damage caused by the escape of operating uid.
To check the return valve, the shut-o valve must be closed and no water may ow out from the opened test valve. The safety
valve must be checked according to DIN 1988 or ÖNORM B2531.
The water heater is operated using the hot water valve on the service water tting. This means the tank is under continuous
line pressure. To protect the internal boiler against overpressure when heating up, the expansion water created is dispersed
through the safety valve every time it is heated. The return valve prevents hot water from owing back into the cold water line
when there is a pressure drop and thus protects the boiler from heating when no water is present.
The shut-o valve can be used to isolate the tank on the water side and thereby eliminate the pressure from the cold water
supply, also allowing use of the waste valve when necessary.
In order to allow for a trouble-free repair, a removal or exchange of the device, it is necessary to establish the connection
of the tank by means of a detachable connection (Dutch). Tank leaks as a result of an improper connection and resulting
damage and consequential damage are excluded from the warranty and product liability.
3. CIRCULATION CONNECTION
Due to signicant energy loss, a circulation connection should be avoided when possible. If a highly branched service water
network requires a circulation line, this must be well insulated and the circulation pump controlled via a timer and ther-
mostat. The switching temperature of the thermostat should be kept low (45°C). The circulation connection piece has an
external thread.
Tank
Safety valve
Waste valve
Non-return valve
Test valve
Pressure reducing valve
Shut-off valve
Service water fixtures
… 18 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Austria Email KRU 052 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Austria Email KRU 052 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 1.7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info