583910
17
Zoom out
Zoom in
Previous page
1/20
Next page
128-7201
17 of 20
CAUTION!
REMEMBER TO RECONNECT THE BROWN/BLACK WIRE TEMPORARILY
DISCONNECTED IN STEP 3
DO NOT RELEASE THIS VEHICLE TO THE CONSUMER UNTIL YOU CONFIRM THE OPERATION
OF THE NEUTRAL SAFETY START FEATURE.
MECHANICAL NEUTRAL SAFETY SWITCH CONSIDERATIONS:
Mechanical neutral safety switch configurations differ slightly in that they do not offer the same level of
safety when installing a remote start device. Often when the ignition switch is turned off while the gear
selector is in any position other than park or neutral, the mechanical function will not allow the key to be
turned to the start position or be removed from the ignition cylinder. This configuration prevents mechani-
cal operation while the vehicle is in gear but offers no consideration for electrical operation. Because of
this potential problem, this installation requires the additional connection of a safety wire from the remote
start device to the vehicle Park/Neutral ECM Input or the vehicle key in sensor. This connection will
prevent remote start operation if the key is left in the ignition switch regardless of the gear selectors
position.
PARK / NEUTRAL ECM INPUT:
The Park / Neutral ECM input is the preferred method of installation. This not only maintains the integrity
of the factory circuit, it is also the easiest to install, providing the vehicle you are working on has this
ECM input.
The installation required for this application (shown below), indicates the slight reconfiguration of the
control switch wiring and the addition of a 4000 series diode. Shown is a typical GM Park/Neutral ECM
input circuit. To connect the Audiovox remote start unit to the GM Park / Neutral ECM input:
1. Locate the Orange / Black reference wire in the "C2" connector found at the ECM in GM B Body
vehicles or, locate the equivalent reference wire in the vehicle you are installing the Audiovox Remote
Start Unit in.
2. Connect the Cathode, (Striped) end, of a 4000 series diode to this reference wire.
3. Connect the Anode, (Non Striped) end, of the diode to one side of the Remote Starts enable switch.
4. Connect the other side of the enable switch to the Black/White enable input wire of the Remote Start
unit.
The reference diagram below shows a typical GM B Body ECM reference wire and how it is to be
connected to the Remote Start Unit.
17
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Audiovox Prestige Platinum APS 686T at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Audiovox Prestige Platinum APS 686T in the language / languages: English as an attachment in your email.

The manual is 0,68 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info