583910

Audiovox Prestige Platinum APS 686T Manual

14
Zoom out
Zoom in
Previous page
1/20
Next page
128-7201
14 of 20
NOTE: When selecting Diesel mode, be certain that the intended vehicle has a true tach reference and be
certain to connect the tach input wire.
To program these selectable features:
1. Turn the ignition key to the ON position.
2. Press and release the pushbutton switch 3 times
3. Immediately turn the ignition key OFF, then back to ON.
4. Press and release the pushbutton switch 2 times.
5. Use channel one button on the transmitter to advance to the feature that you want to change. EXAMPLE
If you need to change programmable feature number 3, press and release button 1 on the transmitter 3 times
in succession. The parking lights will flash 3 times confirming that selected feature 3 can now be
programmed.
6. Use channel 3 button on the transmitter to change the selection of the programmable feature. If you are
not sure what the setting for any feature is, press channel 3 button one time, the parking lights will flash
one, two, three or four times indicating the features setting.
Note: Once you enter the feature programming mode, do not allow more that 15 seconds to pass between
steps, or the programming will be terminated.
2. Programming Tach Rate:
NOTE: All applications require that tach be programmed.
The unit will not operate unless tach is programmed. If an attempt is made to start the vehicle via the remote
start without first programming tach, the unit will flash the parking lights 7 times indicating tach has not been
learned and stored. If the tach rate is not properly programmed to the specific vehicle, the unit may not
realize that the vehicle is running in certain instances reengage the starter motor.
The Remote Car Starter will learn the tach rate of most vehicle's single ignition coils, multiple coil packs,
and or single injector. To learn tach;
1. Turn the ignition key to the ON position.
2. Press and release the program pushbutton switch 3 times.
3. Immediately turn the ignition key OFF.
4. Press and hold the program pushbutton switch, then start the vehicle using the ignition key.
5. When the unit senses the tach signal, the parking lights will begin to flash.
6. Release the program pushbutton switch. The parking lights will turn on for 3 seconds to indicate that the
tach signal is stored and the unit is now out of the program mode.
3. Diagnostics:
1. Be sure that programmable feature number # 10 is set to the "Diagnostics On" mode.
2. Hold the program switch on, then turn the ignition key to the ON position.
3. The lights will flash, and number of flashes will indicate the reason for shutdown on the last remote start
attempt. The indications are as follows.
1 Flash Run Timer Expired
2 Flashes Low, or No Tach Signal
3 Flashes Positive Or Negative Shutdown
4 Flashes Control Switch Moved To Off
5 Flashes RF Shut Down, Remote Signal Received, or Manual Start Input Wire Reactivated.
6 Flashes High RPM Signal Received
7 Flashes Tach Has Not Been Programmed
14
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Audiovox Prestige Platinum APS 686T at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Audiovox Prestige Platinum APS 686T in the language / languages: English as an attachment in your email.

The manual is 0,68 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info