603185
11
Zoom out
Zoom in
Previous page
1/20
Next page
MX822 - Live mixer with 4 mics + 5 lines + 24-bit DSP, 10 FX and USB port
Page 11
English
The unbalanced insert point allows you to insert limiters, compressors, special equalizers or any
other processors on the signal path. The insert (Stereo Jack 6.35 mm) features a closed contact.
When inserting a Jack plug into this connector, the signal path will be cut. The channel signal is
available via the TIP, while the signal feedback is available via the RING.
The mass is transmitted via the body.
The outgoing signals can be used as direct pre-fade and pre-equalizer outputs (the tip and the ring
will then be short-circuited to prevent any signal path interruption).
You will be required to use Y-cables (as described below) if using devices with separated incoming
and outgoing signals.
Ring
Ring
Return (in)
Tip
Tip
Send (out)
Sleeve
Sleeve
Ground/Shield
Insert plug on TRS jack
Sleeve
Sleeve
Output
Input
Ground/Shield
Ring
Ring
Return (in)
Tip
Tip
Send (out)
Mono line-level inputs feature Jack or RCA chassis
onto which you can add balanced or unbalanced
signals.
These inputs can be used to connect synthetisers,
drum machines, direct boxes, etc.
When using unbalanced sources, the ring must be
connected to the body.
RCA inputs can also be used to connect other
sources: CD player, MP3 player, etc.
CAUTION: Please turn the gain settings
of each affected channel to their
minimum before connecting any line-
level signal in order to prevent overloads
and damages to your amplification system.
7.1 - Microphone inputs
7.2 - Line-level inputs
7.3 - Inserts
Microphone inputs feature XLR chassis able to
receive both balanced and unbalanced signals.
These inputs are dedicated to low-level signals.
Connect here low impedance dynamic or condenser
microphones.
These inputs deliver a +48V current required for
condenser microphones once the phantom power
supply has been activated.
CAUTION: Do NOT use balanced sources
once the phantom power supply has
been activated as the voltage delivered
via pins 2 and 3 may cause severe damages to your devices. If using balanced dynamic microphones, please make sure they
are compatible with phantom power supplies.
2 = Hotspot (+)
2
3
1
3 = Coldspot (-)
1 = Ground
Balanced
2 = Hotspot (+)
2
3
1
Shunt between
1 et 3 pins
1 = Ground
Unbalanced
Unbalanced TS
Ring
Ring
Coldspot (-)
Tip
Tip
Hotspot (+)
Sleeve
Sleeve
Ground / Shield
Balanced
Ring
Tip
Tip
Hotspot (+)
Sleeve
Sleeve
Ground / Shield
Shunt between
ring and sleeve
Unbalanced TRS
Tip
Tip
Signal
Sleeve
Sleeve
Ground / Shield
Center
Signal
Sleeve
Ground / Shield
Unbalanced RCA
7 - More about connectors
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Audiophony MX822 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Audiophony MX822 in the language / languages: English as an attachment in your email.

The manual is 1,36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Audiophony MX822

Audiophony MX822 User Manual - French - 20 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info