Manual Audio-Technica M3 - Wireless In-Ear Monitor System (page 10 of 118) (English, German, Dutch, French, Italian, Portuguese, Spanish)

704640

Zoom out

Zoom in

1/118

How to install the batteries in your M3R Stereo Receiver

Each M3R Stereo Receiver uses two 1.5V AA batteries, not included.

Alkaline type is recommended. Always replace all batteries. Make

certain the receiver power is Off before replacing batteries.

1. Open the battery compartment door by sliding tabs in the direction

of the arrows and rotating the door open.

2. Observe correct polarity as marked and carefully insert two fresh

1.5V AA alkaline batteries

3. Close the door, making certain the latches click securely in place.

Note: The M3R Stereo Receiver’s “fuel gauge” battery indicator

displays a maximum of four bar segments. When it flashes

“LOW.BAT”, the batteries should be replaced immediately to

ensure continued operation.

System Operation

Placement:

Location

For best operation, place the M3T Stereo Transmitter near the performance

location. The transmitter should be at least 1 meter (3 feet) from the

receiver. Keep antennas away from noise sources such as digital

equipment, motors, automobiles and neon lights, as well as away from

large metal objects. Audio-Technica recommends that you do not locate

the M3T Stereo Transmitter in the same rack with a wireless microphone

receiver.

System set-up:

1. Plug in the included AC adapter and connect to transmitter’s DC

input.

2. Insert two AA batteries in the receiver, observing polarity as indicated.

3. Power on your receiver (without earphones) with volume in

minimum position. Note: At this point, check to be certain the

RF indictor is not illuminated. If it is illuminated before you

have powered on the transmitter, this means the frequency

you have chosen is already in use. Choose another frequency.

4. Power on the transmitter.

5. Set the receiver and transmitter to the same frequency group and

frequency channel. (See page 17.) Note: Do not set more than

one transmitter to the same frequency.

6. Check the RF LED on your receiver to be certain it is illuminated.

(This indicates that it is receiving a signal from the transmitter.)

7. Power off both units (transmitter and receiver).

Audio set-up:

8. Connect audio source(s) to inputs on the rear panel of the

transmitter. There are two combination audio inputs on the back

panel; each offers both XLR and

" inputs. Use shielded audio

cable for the connection between the transmitter and the audio

source (mixer or instrument). Note: If you want to send the

audio signal through your transmitter (to another transmitter

or recording device, for instance), use the Loop output connectors

on the back of the M3T Stereo Transmitter. The R/2 XLR jack

duplicates the unprocessed signal of the R/2 input; the L/1 XLR

jack duplicates the unprocessed signal of the L/1 input. These

are not affected by front panel settings.

9. Turn on the transmitter.

10. Set the attenuator on rear panel of transmitter to appropriate level.

If AF level indicators (on right side of transmitter LCD) are consistently

at or above +3, set the attenuator to -10 or -20 dB or turn the trim

down for corresponding audio input.

11. Trim levels are set at the factory to the maximum position; adjust if

necessary. (See page 12.)

12. Plug earphones into jack on receiver. Turn the locking ring

clockwise until tight. NOTE: Do not put the earphones in your

ears at this point.

13. Turn on receiver with volume in minimum position.

14. With volume on receiver at minimum position, put earphones into

your ears and gradually increase volume until appropriate level is

reached.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Audio-Technica M3 - Wireless In-Ear Monitor System in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 4,06 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Audio-Technica M3 - Wireless In-Ear Monitor System Manual

Product: