Manual ATTACK Pellet 30 Automatic Plus (page 22 of 60) (English)

810507

Zoom out

Zoom in

1/60

Hose should not be straight, but not too bent – otherwise, pellets would accumulate

and stuck in it. Connect feeder into socket on the rear boiler side.

BURNER START

Burner is automatically turned into standby mode by switching the main boiler switch. The

burner is switched on via the touch screen. Based on the heat supply requirement, the

burner ignites and burns the pellets until the boiler temperature sensor gives a switch-off

signal.

BURNER SHUT DOWN

Burner is turned off by the stop signal from operating thermostat or room thermostat.

EMERGENCY SHUT DOWN

ATTENTION! In emergency case can be burner turned off by the main boiler switch

and disconnection of boiler power plug from electrical socket.

CLEANING AND MAINTENANCE

Burner has to be cleaned after every consumption of 2.000 kg pellets. It is based on

assumption, that boiler keeps adequate amount of ash and the quality pellets are used. It is

also recommended to sweep boiler exchanger parts at least 2x a month.

1.Clean pellet inlet into burner by bottle brush or other suitebla kit

2.Scrape ignition plate a grate and clean the holes in grate

3.Open the lid of turbulators and remove remaining dust (e.g. by vacuum cleaner). Make

sure, that dust is not hot and it cannot burn bag of vacuum cleaner.

4.Once in 3 months it is necessary to dismantle rotary chimney part and to remove

accumu-lated dust.

ATTENTION! Keep ash in closed containers from inflammable material.

Maintenance once a year or in case of need (by a qualified person)

Turn off the boiler with the main switch, disconnect boiler plug from electrical socket.

Open door with burner for approximately 90°.

1. Dismantle burner covering and clean photocell by cloth and soft abrasive detergent

(tooth paste). Be careful by flat cable and buttons of display!

2.Clean blades of ventilator – it is the best to blow them with compressed air.

3.Dismantle scraper and ignition plate.

4.Clean space behind ignition plate

5.Scrape ignition plate and scraper

6.Brush the grate properly and clean holes in grate

7.Assemble all the parts back

8.Clean container and pellet feeder from dust and small dirts 9.Check state of the pellet

inlet hose.

10.Start pellet feeder by connecting the plug into electrical socket (230 V~) to fill it with

pellets.

11.Adjust the amount of pellets to be supplied

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of ATTACK Pellet 30 Automatic Plus in the language / languages: English as an attachment in your email.

The manual is 0.97 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of ATTACK Pellet 30 Automatic Plus

ATTACK Pellet 30 Automatic Plus User Manual - German - 56 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

ATTACK Pellet 30 Automatic Plus Manual

Product: