810554
27
Zoom out
Zoom in
Previous page
1/36
Next page
27
2.5. Errors/breakdowns
Others errors/breakdowns non displayed
In case that the boiler has an error/breakdown and it is necessary to call service, don't try
to remove the breakdown by yourself. There is a dangerous of a threat of electric shock!
Critical
defect Importance Reset Possible cause Elimination
Archive of
breakdowns
symbol
1Invalid sensor of heating water
(shunt fault). Automatic Invalid sensor or cable fault. Call service Err3
2Invalid sensor of TUV
temperature (shunt fault) Automatic Invalid sensor or cable fault. Call service Err3
3Invalid sensor of temperature in
the reference room (shunt fault) Automatic Invalid sensor or cable fault. Call service Err3
4Loose of pressure in the
heating system Manual reset of
the boiler
Water underpressure of heating system = under
0,4 bar.
Control tightness of heating
system, fill the water ane reset
the boiler.
Err1
5Boiler overheating Manual reset of the
emergency
thermostat
The temperature in the boiler is higher than
emergency one - for example the pump
breakdown, breakdownof heating element,
aeration...
Call service Err2
6Electronics breakdown Automatic Wrong connection of realy mode or TUV mode
or invalid control unit. Call service Err4
7Floor overheating Automatic Temperature of heating water set by limitation
thermostat of underfloorheating is higher. Call service Err2
8Breakdown in inlet supply
(overvoltage in the network) Automatic Overvoltage on the inlet clamps of the control
unit. Call service Err4
99 More than 1 breakdown in one
time. - More than 1 breakdown in one time, failures are
displayed in turns. Call service -
Table of errors/breakdowns displayed
Breakdown Possible cause Elimination
The text „Rele Modul Error“ is displayed after the
boiler start.
Wrongly connected relay mogul, defective relay modul,
defective control system
Restart the boiler, in case that the breakdown has not been
eliminated, call service.
Boiler display is not lightening Mistake in inlet supply of the boiler, network under-
voltage, invalid control unit or software is missed.
Restart the boiler, in case that the breakdown has not been
eliminated, call service.
Temperature displayed is not in accordance with
real temperature value Sensor is disconnected or invalid or broken. Call service.
It is not possible to connect GSM modem The net falls short of GSM protocol, wrong PIN,
defective GSM modul Control the PIN code edited by the parameter P29.
Wrong format of user phone number. Control the format of phone number edited by the
parameter P30, P31, P32.
Wrong format of SMS´ s instruction. Control the format SMS according to the description in the
chapter "Installing" including interspaces.
Wrong receiver´s data (SIM card in the boiler). Control if the phone number of SIM card of the boiler is
correct written.
SIM card has not a free memory capacity for receiving
of SMS. Delete all SMS from the SIM card of the boiler.
SIM card is blocked by the GSM operator. Call your GSM operator SIM card of the boiler.
It is not possible to control the boiler by
GSM SMS instruction
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for ATTACK Electric Excellent at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of ATTACK Electric Excellent in the language / languages: English as an attachment in your email.

The manual is 3.14 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info