810499
12
Zoom out
Zoom in
Previous page
1/92
Next page
12
1.6.2 ATTACK DPX LAMBDA
Key:
1. – Green indicator light
2. – Yellow indicator light
3. – Red indicator light
4. – Display
5. – Button „+“
6. – Button „–„
7. – Button
8. – Reset of the safety thermostat
Indicator light 1: Lights, when the boiler was started by the button „+“ (5) automatically stops
after the fuel burns down or when the boiler was manually stopped by the
button „–“ (6).
Indicator light 2: Lights in case of the following faults:
incorrectly measured values of the flue gas temperature
see the chapters Errors and alarms
Indicator light 3: Lights or flickers in the case of error or alarm:
STB started–Reset (error, message (3) displayed)
incorrectly measured values of the boiler temperature (error, message (3)
displayed)
too high flue gas temperature (alarm, message (3) displayed)
overheating – do not open! (boiler temperature over 90 °C, display 3 flickers )
see the chapter Errors and alarms
Display 4: Displays the operating data for different settings by errors. If the boiler is
stopped and no fault is displayed, the display illumination is turned off after
15 minutes.
Button 5 (+): The display illumination is turned on after pressing the button for the first
time. The boiler is started after the button is pressed again – then it is
possible to heat it up or to refill the fuel. Also other settings can be done by
this button (see the Button 7 below).
Button 6 (–): Serves to stop the boiler. This function is used only for an emergency stop,
e.g. if there is no water in the heating system or is the sensor for overheating
is not working. Also other settings can be done by this button (see the
Button 7 below).
Button 7 (ĸ): The display illumination is turned on after pressing the button for the first
time. Press the button again to get into the „Options“. Use the buttons „+“
(5) or „–“ (6)to get to the various data or to make settings.
!There are various functions of the buttons 5 and 6.
Button 8: Reset the button of the safety thermostat (STB)
If the STB had been started because of the excessive boiler temperature
(≥95˚C) and the boiler temperature decreased to 85 °C, you can reset the
STB by removing the cover (8) and pressing the button underneath (8).The
error is automatically removed. If the error occurs again, inform the
technician.
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for ATTACK DPX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of ATTACK DPX in the language / languages: English as an attachment in your email.

The manual is 11.03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of ATTACK DPX

ATTACK DPX Additional guide - English - 21 pages

ATTACK DPX Additional guide - German - 21 pages

ATTACK DPX User Manual - German - 48 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info