769379
24
Zoom out
Zoom in
Previous page
1/34
Next page
Atomos Ronin – User Manual Edition 1: June 2013 22
9. Timecode
Using Timecode
Touching the timecode display on the Ronin’s home screen, just below
the four main coloured controls, will take you to the Timecode setup
screen (this is also accessible by touching Menu and then Timecode)
Occupying the lower-centre part of the screen is the timecode display
with controls to set the start-time of the timecode.
The four timecode modes supported are:
• HD-SDI
• Time of Day
• Record Run
• Auto Restart
Cycle through these modes by touching the timecode Source Selector.
HD-SDI embedded timecode
With this setting, the SDI input will set the timecode (as long as the
source SDI device supports this). The controls to adjust the timecode
value are disabled in this setting because the embedded timecode in the
SDI signal sets the Timecode value of the recording. If you want to adjust
this please, refer to the manual of your SDI input device.
Trigger from HD-SDI time code
If HD-SDI timecode is selected and the camera is in Record Run mode,
the user has the choice to start and stop recording remotely from the
Source Camera HD-SDI timecode.
To enable rolling Timecode Start/Stop functions, simply press the TC
Icon shown here. When enabled, pressing the camera Record Stop/Start
button will make the Ronin start and stop record simultaneously as the
timecode starts and stops.
OFF DISABLED ENABLED
When using the camera in Free Run timecode, the rolling timecode
trigger might not work as expected. However, depending on the
camera, you can trigger record function by the embedded flag/trigger
in the HD-SDI signal. Most higher end cameras have this functionality;
if unsure contact us at support@atomos.com
Time of Day
With this selected, each new clip that is created will contain embedded
timecode accurately showing the time of day that it was recorded,
based on the internal Ronin Time of Day clock. This can be set in
Menu > Date & Time
If recording is stopped and then restarted while in this mode, there will
be a time gap between the last clip and the next one, equal to the length
of time the Ronin has been out of record. The start timecode of each clip
will be the exact time of day when recording started.
Time of Day timecode is useful as a reminder of the time that clips were
recorded. It can also help with syncing-up of multiple cameras, but remember
that the accuracy of the correlation of Time of Day timecode between
Ronins will depend on how closely their internal clocks are synchronised.
In Time Of Day mode, the controls on the Timecode Setup Scre en for
adjusting the start-point of the Ronin timecode are not available, as
the timecode is set by the Ronin’s internal clock.
Record Run
With this setting you set the start timecode of the first clip and the
following clip will start at the frame immediately after the out point of
the preceding clip. This will continue for all clips that follow. This is often
referred to as continuous timecode.
Auto Restart
With this setting, the timecode will be reset to the timecode you define
here whenever you press record. All your clips will start at this timecode.
To adjust the timecode use the “+” and “-” above and below the
hour:minute:seconds sections
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Atomos Ronin at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Atomos Ronin in the language / languages: English as an attachment in your email.

The manual is 2.5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info