810418
26
Zoom out
Zoom in
Previous page
1/44
Next page
DE
www.atmos.cz
26-DE
Bedienungsanleitung - DE
Die durch den Belimo-Stellantrieb /29/ betätigte Klappe wird durch den
Abgasthermostat 2 /28/, der an der Kesselseite positioniert ist. Falls die
Abgastemperatur niedriger ist, als der Sollwert am Rauchgasthermostat 2
(z.B. beim Anlauf des Kessels auf Leistung), wird die durch den Belimo-
Stellantrieb betätigte Klappe auf Maximum geöffnet.
Falls die Abgastemperatur höher ist, als der am
Rauchgasthermostat 2 eingestellte Wert, wird die
durch den Belimo-Stellantrieb betätigte Klappe
auf den standardgemäß vom Hersteller auf 10 mm
(DC 18 GSE - DC 40 GSE), 20 mm (DC 50 GSE)
eingestellten Anschlag geschlossen. Dadurch wird erzielt, dass der Kessel bei seinem
Betrieb die Nennleistung nicht überschreitet und nicht zu hohe Abgastemperatur
erreicht wird. Dieser Wert kann bei Bedarf durch Verschiebung des Anschlags am
Stellantrieb angepasst werden. Der Rauchgasthermostat 2 wird so eingestellt, dass
der Kessel auf Nennleistung hochgefahrenwird (nach 2 Betriebsstunden) und bei
empfohlener Betriebs-Abgastemperatur (170 bis 200 °C) wird der Thermostat 2 so
bewegt, bis es knacks. So wird die Umschaltlage des Thermostats gefunden, die beim
Kesselbetrieb optimal wird.
Einstellung der durch den Belimo-Stellantrieb betätigten Drosselklappe
Einstellung für die Kessel Einstellung für die Kessel
DC 18 GSE – DC 40 GSE DC 50 GSE
Optimal .............................. 10 mm Optimal .............................. 20 mm
Maximal............................. 45 mm Maximal............................. 45 mm
Minimal ............................. 5 mm Minimal ............................. 10 mm
24. Vorgang für optimale Kesseleinstellung
Um bei der Emissionsmessung und beim Wirkungsgrad der ATMOS-Kessel möglichst gute Ergebnisse
zu erreichen, sind folgende Grundbedingungen zu erfüllen:
Brennstoff: Holz
Holzart: 1. Buche (ist der beste und garantierte Brennstoff)
2. Kiefer, Fichte (Ersatzbrennstoff)
Holzfeuchte: empfohlen 12 - 15 %
Holzgröße: Holzscheite (Hälften, Viertel) mit einer Umkreisgröße von 100 bis 150 mm. Holzlänge siehe
Bedienungsanleitung (330 bis 530 mm je nach Kesseltyp).
Schornsteinzug: Ist gemäß der Bedienungsanleitung einzuhalten.
Beim Kesselbetrieb und – messung darf es zu keinen großen Druckänderungen kommen. (z.B. in Folge vom
Wind) Maximum ± 2 Pa (0,02 mbar).
A
A
B
B
5 - 45 mm
DC 18 GSE 16 Pa (0,16 mbar)
DC 22 GSE 18 Pa (0,18 mbar)
DC 25 GSE 18 Pa (0,18 mbar)
DC 30 GSE 20 Pa (0,20 mbar)
DC 40 GSE 22 Pa (0,22 mbar)
DC 50 GSE 24 Pa (0,24 mbar)
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Atmos DC 18 GSE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Atmos DC 18 GSE in the language / languages: German as an attachment in your email.

The manual is 2.27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info