810412
22
Zoom out
Zoom in
Previous page
1/66
Next page
EN
www.atmos.cz
22-EN
Operation and Maintenance Manual - EN
worm conveyor will stop. The burner fan will be started at the ignition speed - parameter S2
as well as the extraction fan.
After the ignition of pellets the photocell will sense light, which will cause the ignition spiral to
switch off with a slight delay.
The burner will pass over to the stage of perfect burning of fuel - set by parameter T7.
The OPERATION algorithm consists of the following steps:
When the fuel burns perfectly, the burner will get to the stage of gradual increase of the power
to the nominal value - parameter T10.
After achieving the nominal power the burner works in the normal mode until the heating system
or the accumulation tank is heated to the required temperature. The power of the burner results
from the hourly quantity of pellets delivered by the worm conveyor to the combustion chamber.
The worm conveyor works in the intermittent mode set by parameters T4 and T6. Parameters
T4 and T6 are set in accordance with the instructions on page 25.
After setting the nominal power of the burner you must also set the amount of combustion air
necessary for complete burning of fuel. The setup is done using air flap of the burner fan and by
changing speed of the burner fan (parameter S3). The exact setting should be carried out by a
trained person with the use of a flue gas analyzer.
The burning out algorithm is designed as follows:
After the achievement of the set temperature at the boiler thermostat (e.g. 85 °C) or temperature
in the accumulation tank - temperature at the bottom sensor (TS), the electronic control unit of the
burner will switch off the external worm conveyor. Thanks to this, the pellets in the combustion
chamber will burn out. Optimal burning out of pellets in the combustion chamber is additionally
supported by the operation of the burner fan for a certain time - parameter T5. After subsequent
drop of the temperature of water in the boiler or discharge of the accumulation tank - temperature
at the top sensor (TV), the burner will be re-started in the same way as described in the text above.
If the accumulation tank is connected to a solar exchanger and activating functions for automatic
optimization (switching) of sensors, parameter S15 = 3, the burner may be turned off by sensor TK
instead of sensor TS.
The other algorithms are designed in the following way:
If the first attempt for ignition with fuel supply fails, the burner will repeat the whole algorithm.
After the second unsuccessful attempt for ignition with fuel supply the burner will proceed to the
third attempt during which the fuel is not supplied any longer, but only the ignition spiral is active.
After this unsuccessful attempt the burner will be put out of operation as the system has probably
run out of pellets or a fault has occurred.
In case of a short-term interruption of power supply to the burner, the burner will automatically
renew its operation after performing diagnostic checks, complete burning out of pellets,
pneumatic cleaning of the burner and a new start.
INFO - This sequence has been set intentionally to ensure safe and trouble-free operation
of the burner.
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Atmos A85 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Atmos A85 in the language / languages: English as an attachment in your email.

The manual is 2.45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Atmos A85

Atmos A85 User Manual - German - 60 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info