810413
51
Zoom out
Zoom in
Previous page
1/72
Next page
Operation and Maintenance Manual - EN
EN
www.atmos.cz EN-51
f) S68 = 11….. Reserve function for controlling boiler exhaust fan for DCxxSP(X), CxxSP,
ACxxSP boiler types when the function for automatic start after wood is burnt out is activated.
This function ensures that boiler exhaust fan is running only during wood burning after the wood
is burnt out. When the burner is run on pellets, the boiler exhaust fan remains switched off. This
function is used if you do not need or want to use the boiler exhaust fan while the burner is run-
ning. Install the AD02 module under the instrument hood of the boiler and connect it electrically
between the boiler terminal board and the extraction fan, see the wiring diagram.
WARNING – this is not a standard setting for DCxxSP(X), CxxSP, ACxxSP boilers with
the function of automatic start
(AUTOSTART – S34 = 1 or S34 = 2) after wood is burnt out (setting is S68 = 4).
g) S68 = 12…..Reserve function for direct control of pump in the boiler circuit from the burner
regulation (boiler terminal board). This function controls the pump in the boiler circuit without
using AD02 or AD03 modules. This is applicable only for boilers that do not allow heating with
wood (not even in emergency situations). E.g. D14P, P14, D21P, P21, D25P, P25, DxxPX, PXxx.
Pump output must be switched to reserve R5 on the boiler terminal board and the TK sensor must
be installed before this function can be activated. After activation, S37, S38, S39, S40 temperature
parameters must be checked and configured.
h) S68 = 13…..Reserve function is the reverse output function for controlling the pump in
the boiler circuit from the burner regulation (output cable from boiler with a connector – white
inside) via AD02 or AD03 modules. This function controls the pump in the boiler circuit using
AD02 or AD03 modules ranged into a set with pump thermostat installed into the boiler panel.
This method of pump controlling can be used for any ATMOS pellet boiler, and is therefore
recommended. AD02 or AD03 modules must be inserted and connected under the boiler hood
and the TK sensor must be installed before this function can be activated. After activation, S37,
S38, S39, S40 temperature parameters must be checked and configured.
i) S68 = 14….. Reserve function for direct control of solar heating pump from the burner regulati-
on (boiler terminal board). This function control solar pump when automatic sensor switching fun-
ction is activated (S15 = 3), where the boiler is connected with accumulation tank equipped with
solar exchanger and collectors. The system requires TV, TK, TS and solar sensors to be connected
to the TSV solar panel. This function never uses AD02 or AD03 modules.
After activation, S26, S27, S28, S29, S30, S31, S32, S33 temperature parameters must be checked
and configured.
This function is specially designed for boilers: D14P, P14, D15P, P15, D20P, P20, D21P, P21,
D25P and P25
CAUTION - the direct controlling function of solar heating from pellet burner cannot be
used for DCxxSP(X), CxxSP, ACxxSP boilers and boilers with burner built into the upper
doors. This function also cannot be used when the pump is simultaneously controlled in the
boiler circuit from the burner regulation (TK sensor cannot be simultaneously in boiler and
accumulation tank).
51


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Atmos A25SP at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Atmos A25SP in the language / languages: English as an attachment in your email.

The manual is 4.12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info