Before starting the assemblyof the solar heater, take into account the following directions :
- The solar heater should be placedin a way that itscollector seethe south (in the northern hemisphere) or seethe north (in the southern hemisphere),
- The place, that you will place the solar heater, must not be shaded and should be as near as possible to consumption,
- During works, the collectors shouldbe covered from the sunto prevent any damage on the closed loop of the system,
- During the set-up, first fill the tank with thedomestic cold water before filling thesolar circuit with the antifreeze/water mixture (at least 15% antifreeze),
- The anti-freezing and anti-corrosive liquid delivered should be added to the closed loop afterit has been diluted withwater. Concentration must fit to the place,
- As temperature of over 60°C occur in the system a suitable domestic hot water mixing valve must be used on the domestic hot water side to avoid scalding.
SPECIFICATIONS:
The thermosyphon system comprises the following components: solar tank, collector(s), frame and installation kit (a detailed listing may be found below)
The maximum operating pressure on the domestic hot water side is 6 bars. A pressure reducer is recommended in the event that the domestic hot water pressure
is higher. The maximum pressure in the closed solar circuit is 1,5 bars. The solar tank is enamelled on the inside and equipped with two sacrificial magnesium
anodes to inhibit corrosion. 1,2 propylene glycol is used to provide frost and corrosion protection in the solar circuit.
PACKAGING AND TRANSPORT:
The system is packed in such a way as to prevent damages as far as possible. The products must be stored away from effects of the weather.
The packaging must be removed if the products are temporarily stored outdoors.
INSTALLATION GUIDELINES:
Before installing the system, ensure that the mounting surface (roof surface) will withstand the weight of the thermosyphon system when filled. Written confirmation
must be obtained from the architect/designer. The system must be installed at least 1m from walls or at the end of the roof to assist with maintenance of the system.
The piping must be sealed with a suitable roof insertion to prevent moisture getting in the roof. Precise guideline must also be provided by the architect for this.
All connection pipes must be very well insulated and UV resistant. The correct insulating material and insulation thickness must be selected according to local
conditions.
FRAMES:
The roof construction must be capable of withstanding the appropriate wind and snow loads. (1m³ powder snow = 60kg, 1m³ wet snow = 300kg).
The local conditions for snow and wind loads must be taken into consideration when mounting the system. Please consult local dealers for further information.
SAFETY EQUIPMENT:
A pressure relief valve with an opening pressure of 1,5 bars is used in the solar circuit. This valve is mounted on the tank in a ½ inch sleeve. The pressure relief
valve for domestic hot water is also installed in ½ inch sleeve above the tank.The solar pressure relief valve can also be fed through the overflow hose into a
container to trap the glycol.
WARNING: the collector should be covered before and during filling.
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Atlantic Solerio Select at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Atlantic Solerio Select in the language / languages: English, French as an attachment in your email.
The manual is 3,19 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
