613624

Atlantic Shangai Ecodomo Manual

8
Zoom out
Zoom in
Previous page
1/22
Next page
2) Fixing the comfort temperature :
The comfort temperature is the temperature that you would like while the room is occupied.
a) Put the switch to
b) Set the control knob on 5, the heating indicator V1 comes on if the room temperature is below the required
temperature.
c) Wait a few hours for the temperature to stabilise.
d) If the setting is satisfactory (if necessary use a thermometer to check), mark the position for future use.
If the setting is not satisfactory, adjust it and start again from point c.
3) Fixing the Eco temperature :
This is the required temperature during periods when the room is unoccupied. It is recommended theat this mode should
be used if the room is unoccupied for more the 2 hours.
a) Set the cursor switch knob to
a) Adjust the control knob between 3 and 4, the heating light V1 comes on, if the ambient temperature is lower than the
instruction of desired Eco temperature.
b) Wait a few hours until the temperature stabilizes.
c) If the setting is satisfactory (if necessary use a thermometer to check), mark the podistion. If the setting is not
satisfactory, adjust it and start again from point c.
Note : When switching n°1 (on the picture) is set on Programming system (clock symbol) with the PassProgram On/
Off, please refer to paragraph n°8.
4) Frost-Free mode :
This mod e is used to keep the temperature at approximately 7°c in the room when you are absent from the house for
a prolonged period (i.e. mor than 24 hours).
a) Set the switch on
.
5) The heating indicator : V1
This light comes on when the heating element is working. It may flash when the temperature has stabilised.
6) Switching off the device :
Move the cursor to .
7) Locking the controls :
66
66
6
It is possible to lock or limit use of the control knob and lock the switch to
prevent unauthorised manipulation of the panel heater (children, etc.).
a) Unhook the panel heater from its wall mounting.
b) Remove the slugs P on the back of the thermostat fro their mountings.
c) Select position B to lock the control knob or position L to limit the amount it
can be turned. Position M blocks the switch.
8) Using the pilote wire :
The product with pilote wire can receive the following signals from a master unit :
- Comfort (temperature of control knob)
- eco (comfort temperature -3°C to -4°C)
- Frost free (approximately 7°C)
- Off
Put the switch to the programming mode (clock symbol).
The product must be connected through the pilote wire to a programming control or a product equipped with pass
program system in order to use these different modes. You can control several convectors with a single programmer
or a product equipped with pass program system;
Warning : The control unit will consider frost free and off signals in any switch selection.
66
66
6
7
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Atlantic Shangai Ecodomo at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Atlantic Shangai Ecodomo in the language / languages: English, French, Portuguese, Spanish as an attachment in your email.

The manual is 0,83 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info