Manual Atlantic F17CP Odyssee (page 5 of 32) (English, German, Dutch, French, Polish, Portuguese, Spanish)

613620

Zoom out

Zoom in

1/32

The product you have just purchased has undergone numerous tests and inspections to guarantee the highest quality. We hope it will give you entire

satisfaction.

INSTALLATION OF THE PANEL HEATER

Please read the instructions before starting to install the heater. Disconnect

the power before carrying out any work on the heater. Keep these

instructions even once you have installed your heater.

1) Where to install your heater ?

- This equipment was designed to be installed in a residence. Please ask your

distributor before using it for any other purpose.

The panel heater should be installed according to normal trade practice and in

compliance with legislation in the relevant country (the IEE Wiring Regulations).

- The equipment is class 2 and is protected against splashed water IP

24. The device is to be installed so that switches and other controls cannot

be touched by a person in the bath or shower, except in the UK where IEE

Regulations 701.512.2 and 701.512.3 apply. These allow the use of IP24

rated products and their integral controls in Zone 2 and outside zones.

- Comply with the minimum clearance distances for positioning of the panel

heater.

- If your wall covering is laid on foam, a spacer the same thickness as the

foam must be placed under the panel heater’s support. This ensures there is

free space behind the panel heater to make sure its control settings are not

adversely affected.

- Do not install the panel heater:

c In a draught that might affect adjustment (for example, under a

central mechanical ventilation unit etc...).

c Under a xed mains power socket.

c In zone 1 of bathrooms a.

It is forbiden to install vertical product in horizontal position.

2) How to install the panel heater ?

2-1) Release the appliance’s hook-on bracket 

We recommend that you place the radiant panel at, face down.

Have a straight head screwdriver to hand.

2-2) Fix the hook-on bracket 

Use the wall-mounting bracket as a template for positioning the heater.

Drilling points A

Drilling points B

Note : Do not use the device in mobile or feets or on casters.(diagram 3C)

2-3) Connecting the panel heater

- The appliance should have a 230-240V 50Hz power supply.

- The panel heater must be connected to the mains, either by a 2-wire cable

(Brown = Phase, Blue = Neutral) via a power socket (Product with plug :

diagram A) or connexion box (Mechanical thermostat : diagram B) ; by a

3-wire cable (Brown= Phase, Blue = Neutral, Black = Pilot wire) by means of

a connexion box (version with pilote wire : diagram C).

In humid areas such as bathrooms and kitchens the power socket must be

installed at least 25 cm above the oor.

- The installation should be tted with a double pole break device with a break

of at least 3 mm.

- Connection to earth is prohibited. Do not connect the pilot wire

(black) to earth.

- The heater must be installed by a qualied electrician in accordance with

the local regulations. The heater and the pilot wire (black) must NOT be

connected to earth. If the power cable is damaged, it must be replaced by

the manufacturer or its after-sales service Department or a similary qualied

person to avoid any risk.

If a pilot or piloted panel heater is protected by 30mA differential (e.g.

bathroom) the pilot wire’s power must be protected on this differential

2-4) Lock the appliance on the hook-on bracket f

USING THE PANEL HEATER

1) Description of the control unit : g 

I/0.

Temperature adjustment control knob.

2) Fixing the comfort temperature

The comfort temperature is the temperature that you would like while the

room is occupied.

a) Put the 1 switch to I.

b) Set the 2 control knob to between 4 and 5.

c) Wait a few hours for the temperature to stabilise.

d) If the setting is satisfactory (if necessary use a thermometer to check),

mark the position for future use.

e) If the setting is not satisfactory, adjust it and start again from point c.

3) Frost-Free mode

This mode is used to keep the temperature at approximately 7°C in the room

when you are absent from the house for a prolonged period (i.e. more than

24 hours).

a) Leave the 1 switch on I, set the 2 control knob to

Nota : When switching n°1 (on the picture) is set on Programming system

(Clock symbol) with the PassProgram On/Off, please refer to paragraph n°8.

4) Locking the controls : 

It is possible to lock or limit use of the 2 control knob to prevent unauthorised

manipulation of the panel heater (children, etc.).

a) Unhook the panel heater from its wall mounting

b) Remove the slugs P on the back of the thermostat from their mountings.

c) Select position B to lock the control knob or position L to limit the amount

it can be turned.

RECOMMENDATIONS FOR USE

- There is no point in setting maximum heating, the room temperature will

not rise any quicker.

- When you air the room, disconnect the panel heater by putting the 1

switch to 0.

- If you leave for several hours, remember to reduce the temperature.

Absence for :

less than 2 hours, do not touch the controls.

2 to 24 hours, lower the 2 control knob by two graduations.

more than 24 hours or in the summer, put the 2 control knob to

- If you have several units in a room, let them operate simultaneously.

This will give you a more uniform temperature without increasing electricity

consumption.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Atlantic F17CP Odyssee in the language / languages: English, German, Dutch, French, Polish, Portuguese, Spanish as an attachment in your email.

The manual is 2,87 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Atlantic F17CP Odyssee Manual

Product: