Manual Atika VT36 (page 15 of 119) (English, German, Dutch, Danish, French, Italian, Polish, Swedish, Norwegian, Finnish)

475732

Zoom out

Zoom in

1/119

Electrical safety

 Design of the connection cable according to IEC 60245 (H

07 RN-F) with a core cross-profile section of at least

- 1.5 mm² for cable lengths up to 25 m

- 2.5 mm

for cable lengths over 25 m

 Long and thin connection lines result in a potential drop. The

motor does not reach any longer its maximal power; the

function of the device is reduced.

 Plugs and coupler outlets on connection cables must be

made of rubber, non-rigid PVC or other thermoplastic

material of same mechanical stability or be covered with this

material.

 The connector of the connection cable must be splash-proof.

 When running the connection line observe that it does not

interfere, is not squeezed, bended and the plug connection

does not get wet.

 Wind off completely the cable when using a cable drum.

 Do not drive the device across the extension cable. Make

sure that it is behind you in a secure position. Place the

cable on a path or area that has already been thatched.

 Do not use the cable for purposes for which it is not meant.

Protect the cable against heat, oil and sharp edges. Do not

use the cable to pull the plug from the socket.

 Protect yourself against electric shocks. Avoid touching

earthed parts with your body (e.g. pipes, heating apparatus,

cookers, fridges etc.).

 Regularly check the extension cables and replace them if

they are damaged.

 Do never connect a damaged cable to the mains. Do not

touch a damaged cable before it is disconnected from the

mains. A damaged cable may cause contact with live parts.

 Do not use any defective connection cables.

 When working outdoors, only use extension cables

especially approved and appropriately labelled for outdoor

use.

 Do not set up any provisional electrical connections.

 Never bypass protective devices or deactivate them.

 Only hook up the machine by means of a fault-current circuit

breaker (30 mA).

The electrical connection or repairs to electrical parts of the

machine must be carried out by a certified electrician or

one of our customer service points. Local regulations –

especially regarding protective measures – must be

observed.

Damaged mains leads must be replaced by the

manufacturer or one of their service workshops or a similar

qualified person to prevent dangers.

Repairs to other parts of the machine must be carried out

by the manufacturer or one of his customer service points.

Use only original spare parts, accessories and special

accessory parts. Accidents can arise for the user through

the use of other spare parts. The manufacturer is not liable

for any damage or injury resulting from such action.

Assembly

Front wheels – VT 40 Â

On the left and right side, slide the wheel (16), washer (4)

and lock washer (37) on the axle. Fix them using the screws

M6x12 (36).

Plug the hub cap (17) and the wheel cap (18) on the wheel.

Handle hoop Â

Plug the lower handle hoop (2) in the body. Make sure that it

locks into place.

Fasten the upper handle hoop (1). You can choose from two

handle heights. Use the supplied fasteners (2x machine

knob (5), 2x washer (4), 2x screw M6x45 (3)).

Fix the cable on the handle hoop using the cable holders (6).

Make sure that the cable has enough free motion.

Grass catching bag (8) Â

optional accessory

Pull the impact guard (7) up and hold it.

Hang up the collecting bag (8) on the holders.

Make sure that the collecting bag (8) is in contact with the

bar and the impact guard (7) rests on the collecting bag.

Start-up

Mains connection

Compare the voltage given on the machine model plate e.g. 230

V with the mains voltage and connect the machine to the

relevant and properly earthed plug.

Connect the machine via a circuit breaker switch (residual-

current-operated circuit switch) 30 mA.

 Use connecting or extension cables up to a length of 1.5 m

featuring a core cross section of at least 25 mm².

Mounting of the extension cable

¨ Plug the female connector of the extension cable on the

male connector of the switch-connector combination (9).

¨ Thread the extension cable through the strain relief (10) as a

loop and hang it up. Â

¨ Make sure that the extension cable has enough free motion.

Switching on / off

Do not use any device where the switch can not be

switched on and off. Damaged switches must be repaired or

replaced immediately by the customer service.

The device is equipped with a safety circuitry preventing

inadvertent switching on.

Only start the machine when it is placed on a flat lawn

area with short grass (shorter than 4cm) and without

obstacles.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Atika VT36 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 2,61 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Atika VT36 Manual

Product: