519928

Atika ST 200 N Manual

17
Zoom out
Zoom in
Previous page
1/110
Next page
16
Maintain your radial tile cutter with care:
− Keep the tools sharp and clean to be able to work better
and more safely.
− Follow the servicing instructions and the information
about changing tools.
− Keep handles dry and free of oils and grease.
Check the machine for possible damage:
− Before continuing to use the machine, the protective
devices must be inspected to ensure that they work
perfectly and with their intended function
− Check whether the movable parts function perfectly
and do not stick or whether the parts are damaged, All
parts must be correctly installed and fulfil all conditions
to ensure perfect operation of the radial tile cutter
− Damaged guards and parts must be properly repaired
or exchanged by a recognized, specialist workshop;
insofar as nothing else is stated in the instructions for
use.
− Damaged or illegible safety warning labels should be
replaced immediately.
Do not allow any tool key to be plugged in!
Store the unused machine in a dry locked place away from
the reach of children.
Do not carry power tools with the finger placed on the
switch. Make sure that the switch is off before connecting
the mains plug with the outlet socket.
Electrical safety
Design of the connection cable according to IEC 60 245
(H 07 RN-F) with a core cross-profile section of at least
1.5 mm
2
for cable lengths up to 25 m
2.5 mm
2
for cable lengths over 25 m
Long and thin connection lines result in a potential drop.
The motor does not reach any longer its maximal power; the
function of the device is reduced.
Plugs and coupler outlets on connection cables must be
made of rubber, non-rigid PVC or other thermoplastic
material of same mechanical stability or be covered with this
material.
The connector of the connection cable must be splash-
proof.
When running the connection line observe that it does not
interfere, is not squeezed, bended and the plug connection
does not get wet.
Do not use the cable for purposes for which it is not meant.
Protect the cable against heat, oil and sharp edges. Do
not use the cable to pull the plug from the socket.
Wind off completely the cable when using a cable drum.
Regularly check the extension cables and replace them if
they are damaged.
Do not use any defective connection cables.
When working outdoors, only use extension cables
especially approved and appropriately labelled for outdoor
use.
Do not set up any provisional electrical connections.
Never bypass protective devices or deactivate them.
The device must be connected via the fitted PRCD
(residual-current-operated circuit breaker).
The electrical connection or repairs to electrical parts of
the machine must be carried out by a certified electrician
or one of our customer service points. Local regulations –
especially regarding protective measures – must be
observed.
Repairs to other parts of the machine must be carried out
by the manufacturer or one of his customer service
points.
Use only original spare. Accidents can arise for the user
through the use of other spare parts. The manufacturer
is not liable for any damage or injury resulting from such
action.
D
D
e
e
s
s
c
c
r
r
i
i
p
p
t
t
i
i
o
o
n
n
o
o
f
f
d
d
e
e
v
v
i
i
c
c
e
e
/
/
s
s
p
p
a
a
r
r
e
e
p
p
a
a
r
r
t
t
s
s
Pos. Bezeichnung Bestell.-Nr.
1.
Supporting leg 344702
2.
Indicator for longitudinal cutting 364733
3.
Closing plug 364734
4.
Star handled screw M8 x 12 364703
5.
Trough 364704
6.
Table plate 364705
7.
Stopper bar (2 pieces) with scale 364706
8.
Angle fence
364707
9.
Star handled nut M6 for angle adjustment 364735
10.
Guide bar
11.
Scale for mitre cut
12.
Stopper for longitudinal section/transport 364710
13.
Cutting unit
14.
On-off switch
364712
15.
Fan (not illustrated) 364713
16.
Fan cooling
364714
17.
Capacitor (not illustrated) 364715
18.
Handhold 364716
19.
Locking screw for mitre cut
364725
20.
Splash guard
364717
21.
Hose
364719
22.
Covering cap
364720
23. Cooling water pump 364718
24. Screw M5 x 12 364736
25. Disc A 5.3 mm 391672
26. Spring washer A Ø 5mm 390908
27. Front flange 364730
28.
Cutting-off wheel Ø 200 x Ø 25.4 x 2.2
mm
364721
29. Socket wrench SW 19 364723
30. Installation wrench 364722
31.
PRCD (residual-current-operated circuit
breaker)
364041
32. Rear flange 364731
33. Safety label 364010
34. Hexagon nut M 12 LH 364732
… 17 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Atika ST 200 N at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Atika ST 200 N in the language / languages: English, German, Dutch, French, Italian, Polish, Swedish as an attachment in your email.

The manual is 2,19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info