519928

Atika ST 200 N Manual

16
Zoom out
Zoom in
Previous page
1/110
Next page
15
Inhalation of dust
In addition, in spite of all the precautionary measures taken,
non-obvious residual risks can still exist.
S
S
a
a
f
f
e
e
w
w
o
o
r
r
k
k
i
i
n
n
g
g
In case of improper usage radial tile cutters can be
dangerous. If electrical tools are used, the fundamental
safety precautions must be met to preclude the risks of
fire, electric shock and injuries to persons.
Before commissioning this product, read and keep to the
following advice. Also observe the preventive regulations
of your professional association and the safety provisions
applicable in the respective country, in order to protect
yourself and others from possible injury.
L
Pass the safety instructions on to all persons who work
with the machine.
L
Keep these safety instructions in a safe place.
Make yourself familiar with the equipment before using it, by
reading and understanding the operating instructions.
Do not use the machine for unsuitable purposes (see
“Normal intended use”).
Mount the machine on a non-slip and level surface (risk of
tipping).
Avoid abnormal posture. Provide a safe standing position
and keep at any time the balance.
Be observant. Attend to what you do. Start working with
rationality. Do not use the device when you are tired or
under the influence of drugs, alcohol or medicaments. One
moment of carelessness when using the device can result in
serious injuries.
Wear suitable work clothes:
− do not wear loose-fitting clothes or jewellery; they can
catch in moving parts.
− Safety shoes
− wear a hair-net if your hair is long
Wear protective clothing:
− ear protection (Sound intensity level at workplace can
exceed 85 dB (A))
− safety goggles
− Protective gloves
− Dust protection mask when carrying out works that
produce a lot of dust
Keep your workplace in an orderly condition! Untidiness
can result in accidents.
Take into consideration environmental influences:
− Do not use the device in moist or wet ambience.
− Do not expose the radial tile cutter to rain.
− Provide for good illumination.
− Do not use this machine near inflammable liquids or
gases.
Never leave the machine unattended.
Children and youngsters less than 18 years of age and
people who have not read the operating manual must not
operate the machine.
Keep other persons away.
Do not allow other persons, especially children, to touch
the tool or cable.
Keep them away from your working area.
Use a lifting device if the weight of the workpiece exceeds
10 kg.
Assume a working position where you are always to the
side of the cutting-off wheel outside of the cut plane.
Do not overload the machine! You work better and safer in
the given performance range.
Only operate the machine with complete and correctly
attached safety equipment and do not alter anything on the
machine that could impair the safety.
Do not use any cracked diamond cutting-off wheels as well
as cutting-off wheels with segmented edge.
Do not use any cutting-off wheels which do not correspond
to the indicated characteristics of this instruction manual.
Do not use any cutting-off wheels which have a maximum
rotational frequency of less than 3000 revolutions per
minute.
Always use diamond cutting wheels having an MPA
overprint with a number.
Choose a diamond-tipped cutting-off wheel that is suited for
the material to be cut.
Do not exceed the safe operating speed of the cutting-off
wheel.
Do not perform dry cuts using cutting-off wheels that are
designed for wet cutting.
Do not use the cutting-off wheel for grinding work, e.g. to
grind the edge of a cut tile. Do not perform radius or round
cuts.
Pay attention to that the water pump is covered with water.
The use of other tools and other accessories can
signify a risk of injury for you.
Do not touch electrical components of the machine (e.g.
switch) by wet hands.
Make sure that all plug-type connections are in a dry place
and do not rest on the ground.
Keep water away from electrical parts of the power tool and
from persons within the working area.
Switch the machine off and remove the mains plug from
the socket when
− carrying out repair works
− maintenance and cleaning
− Elimination of failures (that includes also freeing a
blocked cutting-off wheel)
− transport and storage
− Leaving the radial tile cutter (also for short-term
interruptions)
Attention! Cutting-off wheel keeps running for a
moment after switching off! Do not brake the cutting-off
wheel with the hand or lateral pressure.
Wait until the cutting-off wheel has come to a complete stop
and then pull the mains plug out of the socket before
carrying out any adjusting, maintenance and cleaning work.
… 16 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Atika ST 200 N at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Atika ST 200 N in the language / languages: English, German, Dutch, French, Italian, Polish, Swedish as an attachment in your email.

The manual is 2,19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info