519928

Atika ST 200 N Manual

15
Zoom out
Zoom in
Previous page
1/110
Next page
14
After unpacking, check the contents of the box
! That it is complete
! Check for possible transport damage
Report any damage or missing items to your dealer, supplier or
the manufacturer immediately. Complaints made at a later date
will not be acknowledged.
O
O
p
p
e
e
r
r
a
a
t
t
i
i
n
n
g
g
t
t
i
i
m
m
e
e
s
s
Before initiating the device please observe the provisions
pertaining to corresponding laws (regional provisions) for the
noise control.
C
C
h
h
a
a
r
r
a
a
c
c
t
t
e
e
r
r
i
i
s
s
t
t
i
i
c
c
n
n
o
o
i
i
s
s
e
e
v
v
a
a
l
l
u
u
e
e
s
s
Measured as per prEN ISO 3744:2006
Usage of the radial tile cutter with standard cutting-off wheel.
Sound levels L
WA
97 dB(A)
Sound levels at the work-place L
PA
84 dB(A)
The values given are emission values and must therefore not simulta-
neously represent safe workplace values too. Although there is a
relationship between emission and immersion levels, it can be reliably
deduced whether additional precautionary measures are necessary or
not. Factors, which can influence the immersion level currently
existing at the workplace include the duration of the effects, the
special type of the workroom, other noise sources, etc. e.g. the
number of machines and other adjacent processes. The permissible
workplace values can also vary from country to country. This
information should however enable an improved assessment of the
danger and risk to be carried out.
V
V
i
i
b
b
r
r
a
a
t
t
i
i
o
o
n
n
s
s
Vibration level: ahv = 4.3 m/s²
Measuring uncertainty: K=1.5 m/s²
The indicated vibration emission level has been measured according
to a standardised test method and can be used to compare power
tools.
It can also be used for an initial estimate of exposure.
Warning!
The vibration emission level can differ from the indicated value during
actual use of the power tool depending on the manner of usage.
It is necessary to define safety measures to protect the operator that
are based on an estimate of exposure at the actual conditions of
usage (for this, all parts of the operation cycle have to be considered,
e.g. times during which the power tool is cut off and times during
which it is switched on but runs in no-load mode).
The vibration development during practical use of the electric tool may
deviate from the total value specified according to the manner and
way the device is employed. The user must adapt the safety
precautions for personal protection according to his or her own
estimation if the work environment requires this.
N
N
o
o
r
r
m
m
a
a
l
l
i
i
n
n
t
t
e
e
n
n
d
d
e
e
d
d
u
u
s
s
e
e
The radial tile cutter is only provided for the application in
the home and handcraft fields. It is provided exclusively for
cutting small and medium-sized marble and granite slabs,
bricks and tiles of all kinds, according to the machine size.
The device shall not be used for cutting wood or metals.
Risk of injuries existing!
Only workpieces corresponding to the maximum dimensions
of the technical specifications may be processed.
Use only cutting-off wheels appropriate for the machine, no
saw blades.
Only workpieces which have been securely mounted and
aligned can be processed.
The intended usage also includes compliance with the
operating, servicing and repair conditions prescribed by
the manufacturer and following the safety instructions
included in the instructions.
The relevant accident prevention regulations for the
operation as well as the other generally acknowledged
occupational medicine and safety rules must be complied
with.
Any other use is deemed not to be use as prescribed. The
manufacturer is not liable for any type of damage resulting
from this: the user bears the sole risk.
Unauthorised modifications on the radial tile cutter exclude
a liability of the manufacturer for damages of any kind
resulting from it.
The radial tile cutter shall only be assembled, used and
maintained by persons who are familiarised with it and
instructed about the risks. Repair works may only be carried
out by us or by a customer service agent nominated by us.
The machine may not be used in a potentially explosive
environment or be exposed to the rain.
R
R
e
e
s
s
i
i
d
d
u
u
a
a
l
l
r
r
i
i
s
s
k
k
s
s
Even if used properly, residual risks can exist even if the
relevant safety regulations are complied with due to the design
determined by the intended purpose.
Residual risks can be minimised if the “Safety information” and
the “Intended usage” as well as the whole of the operating
instructions are observed.
Observing these instructions, and taking proper care, will
reduce the risk of personal injury or damage to the equipment.
Risk of injury for fingers and hands by contacts with the
running cutting-off wheel.
Risk of injury for fingers and hands by touching the diamond
wheels on not covered sections.
Injury by catapulted workpiece parts.
Expulsion of a faulty diamond attachment of the cutting-off
wheel.
Risk from electricity, by using non-standard electrical
connections.
Touching live parts of opened electrical components.
Impairment of hearing when working on the machine for
longer periods of time without ear protection.
… 15 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Atika ST 200 N at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Atika ST 200 N in the language / languages: English, German, Dutch, French, Italian, Polish, Swedish as an attachment in your email.

The manual is 2,19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info