519953
14
Zoom out
Zoom in
Previous page
1/104
Next page
14
D
D
e
e
s
s
c
c
r
r
i
i
p
p
t
t
i
i
o
o
n
n
o
o
f
f
d
d
e
e
v
v
i
i
c
c
e
e
/
/
S
S
p
p
a
a
r
r
e
e
p
p
a
a
r
r
t
t
s
s
 /
Pos Denomination
Order-No.
RL 1000
1.
Agitator
2.
Mortar beater
a) Bar
b) Beater attachment
372582
Ø120 mm
3.
ON / OFF-switch
4.
Trip switch
5.
Speed control
6.
Handle
7.
Shaft
8.
Carbon brush cover 372660
9.
Carbon brushes (2pcs) 372658
10.
Spanners SW 22 372562
11.
Spanners SW 19 372657
12.
Safety label 372662
13.
Disk beater 372613 Ø114 mm
14.
Spiral beater 372583 Ø120 mm
A
A
s
s
s
s
e
e
m
m
b
b
l
l
y
y
Chucking the beater
 Screw the bar (2a) on the shaft (7). Secure the bar
using the spanners (10/11).
Â
Screw the beater attachment (2b) on the bar (2a) and
secure it using the spanner (10).
S
S
t
t
a
a
r
r
t
t
-
-
u
u
p
p
Do not use any device where the switch can not be
switched on and off. Damaged switches must be repaired
or replaced immediately by the customer service.
Check that the machine is completely and correctly assem-
bled.
Before each use, check
Connection cables for defects (cracks, cuts, etc.).
Do not use any defective cables.
there are no damages at the machine
(see "safe working")
that the beater is properly secured.
Mains connection
Compare the voltage given on the machine model plate e.g.
230 V with the mains voltage and connect the machine to
the relevant and properly earthed plug.
Connect the machine via a 30 mA fault current safety
switch.
Do not use any defective connection cables.
Use connecting or extension cables up to a length of 1.5 m
featuring a core cross section of at least 25 mm².
L Main fuse: 10 A
Switching on/off
Do not use any device where the switch can not be
switched on and off. Damaged switches must be repaired
or replaced immediately by the customer service.
Switching on
 Operate the trip switch (4) at first. Press the ON/OFF
button (3) on the handle.
LStart the machine at the lowest rotational speed (Level 1).
Switching off
 Release the ON/OFF handle button.
L This machine is not suited for continuous operation.
Speed control
With this type, the motor's speed and thus the agitator perfor-
mance can be adjusted. (Level 1 - 6).
Â
You can continuously adjust the speed with the speed
control (5) - n
0
= 0 min
–1
- 1100 min
–1
.
Level 1 £ Min. power = SLOW.
Level 6 £ max. power = FAST.
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Atika RL 1000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Atika RL 1000 in the language / languages: English, German, Dutch, French, Italian, Polish, Norwegian, Finnish as an attachment in your email.

The manual is 1,83 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info