520117
16
Zoom out
Zoom in
Previous page
1/144
Next page
14
¾ Do not allow the shredded material to pile up too high in the
area of the ejection opening. This can lead to shredded mate-
rial blocking the ejection channel, and backing up to the filler
opening.
¾ Clean out the filler opening and ejection channel thoroughly if
the machine becomes blocked. Before doing this, switch the
motor off and disconnect the machine from the mains power
supply.
¾ Please do not exceed the maximum branch diameter speci-
fied (cutting fresh wood) for your appliance ( see “Technical
data”). Depending on the wood’s nature and freshness the
maximum branch diameter the machine can process may be
smaller.
¾ The blades largely pull the material into the machine by them-
selves.
¾ Strong branches may cause overloading. This can be avoided
by pulling them back from time to time.
¾ If the machine is overloaded, a protective motor switch en-
sures that the machine turns itself off automatically.
Turn the shredder on again after about 5 minutes.
If you cannot turn on the machine after this waiting time re-
fer to „Operational faults“.
C
C
h
h
a
a
n
n
g
g
i
i
n
n
g
g
t
t
h
h
e
e
b
b
l
l
a
a
d
d
e
e
s
s
Remove the mains plug before changing the blades.
Risk of injury to the fingers and hands when carrying out
work on the blade unit. Wear protective gloves.
Open the machine.
Fix the blade.
Reduced output
One edge of the knife has become blunt:
Turn knife so that you can use the other edge.
All knive edges have become blunt:
Replace with new set of knives (order-no. 382425).
M
M
a
a
i
i
n
n
t
t
e
e
n
n
a
a
n
n
c
c
e
e
a
a
n
n
d
d
c
c
l
l
e
e
a
a
n
n
i
i
n
n
g
g
Each time before starting maintenance work:
Switch off the motor and pull out the mains plug.
Wear protective gloves to prevent injury.
The cutters will not come to a standstill immediately after
cut-off. Before starting any service work wait until all parts
are stationary.
Be sure to have removed any tools from the machine after
completion of service work.
Generally garden shredders require little maintenance. To
maintain their efficiency and a long life, observe the fol-
lowing:
Keep vent slits clean and free from obstructions.
Check the locking screws (tighten where necessary).
Clean the device after shredding.
To clean your product only use a warm moist cloth and a soft
brush.
Never use cleaning agents or solvents. Otherwise the device
may be damaged irreversibly. Plastic parts may be corroded
by chemicals.
Do not clean the machine with running water or high-pressure
cleaners.
After each operation treat bare metal parts with an environ-
ment-compatible biodegradable spray oil to protect them
against corrosion.
Left-hand thread
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Atika MHA2800 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Atika MHA2800 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 3,14 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info