475722

Atika KS2000 Manual

22
Zoom out
Zoom in
Previous page
1/158
Next page
21
Commissioning
Mains connection
Compare the voltage given on the machine model plate
e.g. 230 V with the mains voltage and connect the saw
to the relevant and properly earthed plug.
Use a shockproof plug, mains voltage 230 V with
residual current circuit breaker (FI switch 30 mA).
Only use connection cables with sufficient diameters.
Mains fuse
16 A insert
Electrical mains supply impedance
When conditions in the electrical mains supply are un-
favourable, voltage reductions for short periods can occur
during the process of turning on the equipment, which can
adversely affect other equipment (e.g., the flickering of a
lamp).
No breakdowns are to be expected if the maximum,
electrical mains supply impedances given in the table are
met.
Power consumption P
1
(W)
Electrical mains supply
impedance Z
max
(Ω)
2000 0,36
Switching On / Off
Do not use a device where
− the contactor can not be switched on and off.
− the chain and motor brake does not work properly
Damaged switches must be repaired or replaced
immediately by the customer service.
When switching on the chain saw must be supported
and held safely. Chain and sword must stand free.
Switch on
Push and hold automatic trip switch (5). Then operate the
On/Off switch (6). Release now automatic trip switch.
Switching off
Release On/Off switch.
Chain brake
The chain brake is a protective mechanism which in case
of a stroke back chain saw is initiated via the front hand
protection or after releasing the on/off switch. The saw
chain stops immediately (< 0,1 sec.).
Checking of chain brake
Check from time to time the function of the chain brake.
Set the chain brake release (3) in pos. 2 and switch on
the chain saw.
Pos. 2 = Chain brake active
Chain saw does not initiate
Set the chain brake release (3) in pos. 1 and switch on
the chain saw.
Pos. 1 = Chain brake released
Saw chain initiates
Clamping of saw chain
Check the saw chain tension before
start of work
after the first steps
during sawing regularly all 10 minutes
☞ Only with a correct clamped saw chain and a sufficient
lubrication you can influence the durability.
Please observe the following:
a new saw chain must be reclamped more often until it
has elongated.
in case of heating of chain to operating temperature it
expands and needs to be reclamped.
After finishing the sawing works release tension of
saw chain as in case of cooling too high tensions would
emerge in the saw chain.
if chain flackers or comes out of the guide clamp it
again immediately.
Clamping of saw chain:
1. Put the chain saw with motor facing downward on an
even face.
2. Loosen the fastening screw (11) 1 – 2 revolutions anti-
clockwise.
3. Turn the chain tension ring (12) stepwise clockwise
until the correct chain tension is reached. The engaging
effect prevents that the chain tension loosens.
The fastening screw (11) turns with it; possibly it
must be released again during the clamping process.
4. The saw chain is correctly clamped when it can be
lifted in the centre of the sword by appr. 3 – 4 mm.
5. Turn the chain tension ring (12) anti-clockwise when
the saw chain is clamped to much.
6. Refasten the fastening screw with the hand.
7. Check wether the chain links are positioned correctly in
the guide slot of the sword.
6
7
8
9
9
10
… 22 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Atika KS2000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Atika KS2000 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Finnish as an attachment in your email.

The manual is 4,09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info