520124

Atika GHB760A Manual

17
Zoom out
Zoom in
Previous page
1/96
Next page
15
Do not overload the machine! You work better and safer in the
given performance range.
Be sure to operate the product with sharp knives or beaters - this
will reduce the risk of kickbacks.
Only operate the machine with complete and correctly attached
safety equipment and do not alter anything on the machine that
could impair the safety.
Only start shredding when the petrol engine has reached its max.
speed.
Do not alter the revolution speed of the engine, since this
controls the safe maximum operating speed, and protects the
engine and all rotating parts against damage due to excess
speed.
Do not operate without the funnel.
Do not modify the device or parts of the device respectively.
Close machine properly before enabling engine.
Do not wash down device with water.
Take into consideration environmental influences:
− Do not use the device in moist or wet ambience.
− Do not leave the machine standing in the rain or use when
raining.
− Do only work with sufficient visibility conditions. Provide for
good illumination.
To prevent danger of injury to fingers during assembly or
cleaning operations wear protecting gloves.
Stop the machine and remove the spark plug connector when
− maintenance and cleaning
− eliminating faults
− carrying out repair works
− transport and storage
− changing the blades
− leaving the garden shredder (even in case of short-term
interruptions)
If the machine’s filling hopper or ejection slot is blocked stop the
engine, disconnect the spark plug connector and wait until the
tools are stationary before removing residual material from the
filling hopper or ejection slot.
Check the machine for possible damage:
− Before further use of the machine the safety devices must be
checked carefully for their proper and intended function.
− Check whether movable parts function perfectly and do not
stick or whether parts are damaged. All parts must be
correctly installed and fulfil all conditions to ensure perfect
operation of the machine.
− Damaged guards and parts must be properly repaired or
exchanged by a recognized, specialist workshop; insofar as
nothing else is stated in the instructions for use.
− Damaged or illegible safety labels should be replaced
immediately.
Store unused equipment in a dry, locked place out of the reach of
children.
Do not allow any tool key to be plugged in!
Before switching on, check always that wrenches and adjusting
tools are removed.
Do not repair the device unless you are qualified for such kind of
work.
Do not carry out repair operations on the machine other than
those described in section “Maintenance” but contact the
manufacturer or authorized customer service centres.
Local regulations – especially regarding protective measures –
must be observed.
Use only original spare parts. Accidents can arise for the user
through the use of other spare parts. The manufacturer is not
liable for any damage or injury resulting from such action.
Safe handling with fuels
Fuels and fuel vapours are inflammable and may cause
serious injury on the skin or when inhaled. Therefore be
careful and provide sufficient ventilation when handling
with fuels.
Stop the engine and allow the garden shredder to cool down
before fuelling it.
Do not smoke and avoid open flames when fuelling.
Wear gloves when fuelling.
Do not fuel in closed rooms (risk of explosion).
Avoid spilling of fuel or oil. Clean the garden shredder
immediately when you have spilled fuel or oil. Change your
clothes immediately when you have spilled fuel or oil on them.
Make sure that no fuel can come into the soil.
Carefully close the tank cap after fuelling and check that it does
not get loose during operation.
Check that there is no leakage on the tank cap and fuel lines. If
there are leaks this device may not be started.
Only transport and store fuels in containers approved and
identified for this.
Keep children away from fuels.
Do not handle and store fuels close to combustible and highly
inflammable materials as well as sparks and open flames.
Go away at least three metres from the fuelling place to start the
device.
A
A
s
s
s
s
e
e
m
m
b
b
l
l
y
y
Two persons are required for assembly.
Close the side hopper using the four nuts M8.
Mount the carrying handles.
You will need: 4 pcs tallow-drop screw M8x35, 4 pcs self-
locking hexagon nut, 12 pcs washer A8.4 - ∅ 16, 4 pcs washer
A8.4 - ∅ 24.
Install the support (12).
At first, install one screw M8x16 together with washer A8.4 and
lock washer A8 each on the left and right side.
Tighten the screws only hand-tight.
Fold up the support.
Then, secure the support with another screw together with
washer and lock washer.
Tighten all screws.
The second person tilts the garden shredder towards himself.
Guide the screws M8x205 through the axle support RH (38)
and then through the device.
Position the distance sleeves (39) and guide the screws
through them.
Then place on the axle support LH (37).
Secure the screws with washer A8.4, lock washer A8 and
hexagon nut M8.
Tighten the hexagon nuts only hand-tight.
Guide the axle (10) through the axle support.
Put the wheels (11) on the axle.
Secure the wheels using the lock washer A5 and the wheel cap
(40).
Remove the both screws.
Mount the storage box (9) and fasten it with the screws
previously removed.
… 17 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Atika GHB760A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Atika GHB760A in the language / languages: English, German, Dutch, French, Italian, Norwegian as an attachment in your email.

The manual is 1,6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info