Manual Atika Favorit 320 (page 17 of 116) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

519922

Zoom out

Zoom in

1/116

Cleaning Maintenance

The concrete mixer requires practically no maintenance.

Additional safety instructions

The mixing drum and drive shaft are bedded on ball bearings with

permanent lubrication.

Pull plug each time before cleaning.

 Never grease the ring gear!

To preserve the value of the mixer and increase its service life,

handle it as described in "Transport and storage". Furthermore,

the concrete mixer should be checked regularly for signs of wear

and tear or functional deficiencies. This applies especially to

moving parts, screw connections, protective devices and

electrical parts.

• Switch off machine and pull plug if you have to touch the

machine (with hand, brush, scraper, rag, etc.) while cleaning

it.

• Protective devices removed for cleaning must be properly

remounted before starting the machine.

• Do not spray water directly on the motor or the switch, nor on

the ventilation apertures in the motor housing.

Repair

L Notes on cleaning:

• Before taking a break and after finishing work, clean the

concrete mixer inside and out.

Pull plug each time before doing repair work.

• Do not pound on the mixing drum with hard objects

(hammer, shovel, etc.). A dented mixing drum impairs mixing

operations and is difficult to clean, besides.

• Switch off machine and pull plug if repair work should be

necessary. Do not start machine during repair work.

• To clean the inside of the drum, put in some water and a few

shovels full of gravel and set the drum to revolving.

• Protective devices removed for repairs must be properly

remounted before starting the machine.

• Remove any concrete or mortar left sticking to the teeth of

the axle-drive bevel gear or the crown gear segments

immediately.

• Only the manufacturer or companies authorised by the

manufacturer may perform repair work on electrical parts or

on parts which affect the space needed to mount electrical

equipment.

• Use only unaltered original spare parts. Otherwise, the

manufacturer will assume no liability.

• Adjust tooth play (if possible) ¨ see P. 113.

Equipment failures

Malfunction Possible cause Remedy

Motor does not start up

⇒ no mains voltage

⇒ defective cable

⇒ check fuse protection

⇒ have checked or replaced (electrician)

⇒ thermostat is triggered « reason:

− motor overload

− motor not getting enough air owing to

clogged ventilation apertures

⇒ allow motor to cool and then find and eliminate

whatever caused the thermostat to respond

Motor hums but does not start

⇒ blocked crown gear

⇒ defective condenser

⇒ switch off machine, pull plug and clean or

replace the crown gear segments

⇒ send machine to manufacturer or a company

designated by the manufacturer for repairs

Machine starts up, but

becomes blocked at low load

and may switch off auto-

matically

⇒ extension cord is too long or its cross-section

is too small

⇒ socket is too far from mains connection and

the connecting wire's cross section is too small

⇒ extension cord must be at least 1.5 mm² for a

maximum length of 25 m; the cross-section of

longer cables must be at least 2.5 mm²

Guarantee

Please observe the enclosed terms of guarantee.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Atika Favorit 320 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4,69 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Atika Favorit 320 Manual

Product: