519923

Atika Compact 100 Manual

7
Zoom out
Zoom in
Previous page
1/36
Next page
• Use only connecting attachments with a rubber plug device
for severe requirements
that is protected against spraying
water.
• Check connecting attachments for defects or ageing before using
them.
• Never use defective connecting attachments.
• When laying the connecting attachments, be sure that they do
get crushed or bent, and that the plug-and-socket connection does
not get wet.
• Do not use any temporary electrical connections.
• Never bridge over protective devices or put them out of operation.
• Only connect with residual current circuit breaker (30 mA).
A licensed professional electrician must make all electrical
connections and repairs, and observe local regulations in doing so,
especially those regarding protective measures.
The manufacturer or a company designated by the manufacturer
must attend to the repair of all electrical parts on the machine.
6
S
S
t
t
a
a
r
r
t
t
-
-
u
u
p
p
Observe all safety instructions.
Setting up the machine:
• Set up the machine on a solid, level base.
• Keep the machine from sinking into the ground or floor.
Adhere to accident prevention regulations (danger of tipping).
• When setting up the machine, make sure that the mixing drum
can be emptied without obstruction.
Switching on and off
Be sure that
- all protective devices are on the mixer and properly mounted.
- all safety instructions are adhered to.
• Switch the motor on and off only at the switch.
• In the event of a power failure, the machine will switch off
automatically. Press the switch again to restart the machine.
Motor protection
The motor is equipped with a thermostat. The thermostat switches the
motor off automatically in the event of overload (overheating). The
machine can be restarted after a cooling-off period.
M
M
i
i
x
x
i
i
n
n
g
g
• Only use mixer for applications listed under ”Correct use“.
• Check the stability of the mixer.
• Only fill or empty the mixing drum while the motor is running.
• Observe the nominal filling volume!
• An electrical safety shutdown prevents the mixer operating while
the safety grid is open. Check functionality of safety shutdown
before commissioning.
Mixture production:
1. Close safety grid.
2. Switch on mixer.
3. Fill with water and aggregate (sand, ...).
4. Add binding agent (cement, lime, ...).
5. Repeat points 3 and 4 until required mixture ratio has been
achieved.
6. Blend mixture well.
Have a professional advise you regarding the composition and
quality of the material being mixed.
Prepared (commercially available) mixture production:
Observe mixing ratio and details given by manufacturer on packaging.
1. Close safety grid.
2. Switch on mixer.
3. Fill with required volume of water.
4. There is a sack opener on the safety grid which is used to tear
open the packed mixture and filling the drum.
5. Blend mixture well.
Emptying the mixing drum:
The drum is emptied through an opening in the base which is opened
by actuating a lever.
See page 29 for instructions on emptying.
T
T
r
r
a
a
n
n
s
s
p
p
o
o
r
r
t
t
Pull plug each time before transport.
For loading see page 30.
S
S
t
t
o
o
r
r
a
a
g
g
e
e
The mixer should be cleaned thoroughly before long storage periods
and moving parts treated with an environmentally-friendly spray oil.
This lengthens the useful life of a mixer and ensures smooth operation
of the device.
C
C
l
l
e
e
a
a
n
n
i
i
n
n
g
g
Additional safety instructions
Pull plug each time before cleaning.
• Switch off machine and pull plug if you have to touch the machine
(with hand, brush, scraper, rag, etc.) while cleaning it.
• Protective devices removed for cleaning must be properly
remounted before starting the machine.
• Do not spray the motor and switch directly with a water jet.
• Remove agitator head to clean (
see page 30).
Notes on cleaning:
• Before taking a break and after finishing work, clean the mixer
inside and out.
• Do not beat on the mixing drum with hard objects (hammer,
shovel, etc.). A dented mixing drum impairs mixing operations and
is difficult to clean, besides.
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Atika Compact 100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Atika Compact 100 in the language / languages: English, German, Dutch, Danish, French, Swedish, Norwegian as an attachment in your email.

The manual is 3,59 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info