519871

Atika BioTec 1600 Manual

13
Zoom out
Zoom in
Previous page
1/61
Next page
12
Risk of injury to the fingers and hands, when carrying out
assembly work and cleaning on the blade unit.
Injury by the chopped material spinning away near the
hopper.
Risk from electricity, by using non-standard electrical
connections.
Touching live parts of opened electrical components.
Impairment of hearing when working on the machine for
longer periods of time without ear protection.
In addition, in spite of all the precautionary measures taken, non-
obvious residual risks can still exist.
S
S
a
a
f
f
e
e
w
w
o
o
r
r
k
k
i
i
n
n
g
g
Before commissioning this product, read and keep to
the following advice. Also observe the preventive
regulations of your professional association and the safety
provisions applicable in the respective country, in order to
protect yourself and others from possible injury.
L
Pass the safety instructions on to all persons who work
with the machine.
L
Keep these safety instructions in a safe place.
L
Machine including safety cut-out
The safety cut-out, including an automatic motor brake,
which is attached to the shredder is used for the safety
of the machine, preventing the motor being started
when the machine is open and the rotating knives could
be reached by the operator’s hand.
Repairs on the safety cut-out must be done by the
producer or by a company designated by the
producer.
Make yourself familiar with the equipment before using it, by
reading and understanding the operating instructions.
Do not use the machine for unsuitable purposes (see 'Normal
intended use' and 'Working with the garden chopper').
Ensure that you have stand in a secure standing position
and maintain your balance at all times. Do not lean forward
over the machine. When placing material into the shredder,
always stand on the same level as the machine.
Be attentive. Be careful what you do. Behave sensibly
when working. Do not use the saw if you are tired.
Wear protective goggles, gloves and noise protection while
working with the machine.
Wear suitable work clothes!
−
Do not wear loose-fitting clothes
−
Slip-proof shoes
Within his area of work the operator is responsible for third
parties.
The machine must not be operated by children or young
people under 16 years of age.
Keep children away form machine.
Never operate the machine if other persons are in the
immediate vicinity.
Never leave the saw unattended.
Keep your workplace in an orderly condition! Untidiness
can result in accidents.
Choose a working position alongside the equipment or
behind it. Never stand near the ejection opening.
Never reach into the filling or ejection opening.
Keep your face and body away from the filling opening.
Do not overload the machine! You work better and safer in
the given performance range.
Only operate the machine with complete and correctly
attached safety equipment and do not alter anything on the
machine that could impair the safety.
Do not alter the revolution speed of the motor, since this
controls the safe maximum operating speed, and protects the
motor and all rotating parts against damage due to excess
speed.
Do not operate without the funnel.
Faulty or damaged parts in the device must be replaced
immediately.
Close machine properly before enabling motor.
Do not spray machine with water
(this is hazardous due to live components).
Do not leave the machine standing in the rain or use when
raining.
Store the unused machine in a dry locked place away from
the reach of children.
To prevent danger of injury to fingers during assembly or
cleaning operations hold the cutting mechanism (see. pic. p.
14) and wear protecting gloves.
Switch the machine off and remove the mains plug from
the socket when
− carrying out repair works
− carrying out servicing and repair
works, removal of faults
− changing the blades
− Transporting
− leaving unattended (even during short interruptions)
Check the machine for possible damage
−
Before continuing to use the machine, the protective
devices must be inspected to ensure that they work
perfectly and with their intended function
−
Check whether the parts are damaged. All parts must be
correctly installed and fulfil all conditions to ensure
perfect operation of the saw
−
Damaged guards and parts must be properly repaired or
exchanged by a recognized, specialist workshop; insofar
as nothing else is stated in the instructions for use.
−
Damaged or illegible safety warning labels should be
replaced immediately.
Electrical safety
Design of the connection cable according to IEC 60245
(H 07 RN-F) with a core cross-profile section of at least
−
1.5 mm
2
for cable lengths up to 25m
−
2.5 mm
2
for cable lengths over 25m
When laying the connecting attachments, be sure that they
do get crushed or bent, and that the plug-and-socket
connection does not get wet.
Do not use the cable for purposes for which it is not meant.
Protect the cable against heat, oil and sharp edges. Do not
use the cable to pull the plug from the socket.
Regularly check the extension cables and replace them if
they are damaged.
Do not use any defective connection cables.
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Atika BioTec 1600 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Atika BioTec 1600 in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 3,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info