520677

Atika BHS 30 Manual

34
Zoom out
Zoom in
Previous page
1/129
Next page
34
S
S
t
t
o
o
p
p
p
p
i
i
n
n
g
g
t
t
h
h
e
e
e
e
n
n
g
g
i
i
n
n
e
e
Release the throttle trigger (9).
Put the ON/OFF switch (10) to the position
.
S
S
t
t
a
a
r
r
t
t
i
i
n
n
g
g
w
w
i
i
t
t
h
h
w
w
a
a
r
r
m
m
e
e
n
n
g
g
i
i
n
n
e
e
Start the device as described under “Starting with cold engine”,
but leave the choke lever in its operating position
and do
not operate the throttle trigger.
W
W
o
o
r
r
k
k
i
i
n
n
g
g
i
i
n
n
s
s
t
t
r
r
u
u
c
c
t
t
i
i
o
o
n
n
s
s
You may not start to operate the machine until you
have read these operating instructions, observed all the
instructions given and installed the machine as described!
Always apply the carrying strap (7) when working
with this machine.
Adjust the carrying strap so that a convenient and safe carrying
of the machine is ensured.
The quick acting closure (A) is located at the front.
The quick acting closure can be opened with the left
hand.
The hip pad (B) should rest on the hip.
Immediately replace a damaged carrying strap.
Always keep your hands and feet at a safe distance
to the cutting tool.
W
W
o
o
r
r
k
k
i
i
n
n
g
g
w
w
i
i
t
t
h
h
t
t
h
h
e
e
b
b
r
r
u
u
s
s
h
h
c
c
u
u
t
t
t
t
e
e
r
r
Kickback – backstroke
When working with metal blades, a kickback of the whole
machine or a sudden pull forwards may occur if fixed objects
(trees, branches, stones or the like) are hit. Such a kickback
occurs abruptly without advance warning and may result in loss
of control of the machine and hazards to the operator and
bystanders. There is a particular hazard in badly visible and
overgrown areas.
To keep the control in case of kickback
• Always hold the machine firmly with both hands when
working.
• Make sure that you have a safe stand. Keep your feet
conveniently spread and be always alert to a possible
kickback.
• Do not overestimate your abilities and always keep your
balance when working.
• The cutting blade should have reached its full speed before
cutting.
When brushcutting, stones and debris may be thrown up
and cause serious injuries. Make sure that the protective hood is
safely mounted.
Failure to install rotating parts (cutting blades) correctly may
result in severe accidents. Check the cutting blade for secure
seating before starting your work.
Mowing
• Incline the machine slightly forward and uniformly move it
from right to left with adequate speed. This way, the cut
material falls on the already mowed area.
• Cut higher grass and denser growth in several passes. For
this, shorten the upper portion of the material to be cut at first
by moving the device to the right. Then, move the device to
the left and cut the lower portion of the material to be cut.
• When working on slopes mow in stripes. Mow a stripe
parallel to the slope. Move then back on the mowed area and
mow the next stripe.
• Adjust the engine speed and cutting height to the prevailing
conditions. If the engine speed is too low, scrub can entangle
in the cutting tool or the cutting tool may get stuck in the
scrub.
If grass, scrub or other objects entangle in the cutting tool or
if the device vibrates abnormally, immediately stop the engine
and check the machine.
- A blocked angular gear may cause coupling damage.
- Never remove jammed material while the cutting blade is still
rotating. Wait until the cutting blade stands still.
- If the cutting blade is dull, broken or bent, replace it by a
genuine spare part.
W
W
o
o
r
r
k
k
i
i
n
n
g
g
w
w
i
i
t
t
h
h
t
t
h
h
e
e
g
g
r
r
a
a
s
s
s
s
t
t
r
r
i
i
m
m
m
m
e
e
r
r
Trimming
• Incline the machine slightly forward and uniformly move it
from left to right with adequate speed.
• You will get the best trimming results when you cut dry grass.
•
Do not guide the cutting thread directly at walls and
paving stones. Otherwise it will prematurely wear off.
• Cut higher grass and denser growth in several passes to
prevent the spool head from becoming blocked.
A blocked spool head may cause coupling damage.
• Adjust the engine speed and cutting height to the prevailing
conditions. If the engine speed is too low, scrub can entangle
in the cutting tool or the cutting tool may get stuck in the
scrub.
If grass, scrub or other objects entangle in the cutting tool or
if the device vibrates abnormally, immediately stop the engine
and check the machine.
- A blocked spool head may cause coupling damage.
… 34 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Atika BHS 30 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Atika BHS 30 in the language / languages: English, German, Dutch, French, Italian, Swedish as an attachment in your email.

The manual is 1,62 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info