520677

Atika BHS 30 Manual

29
Zoom out
Zoom in
Previous page
1/129
Next page
29
• Stop the machine and remove the spark plug connector
when
− the cutting tool comes in contact with stones, nails or
other foreign objects
− carrying out repair work.
− performing maintenance and cleaning work.
− Eliminating faults.
− transporting or storing
− replacing the cutting tool
− leaving of machine (also for short-term interruption)
S
S
a
a
f
f
e
e
t
t
y
y
i
i
n
n
s
s
t
t
r
r
u
u
c
c
t
t
i
i
o
o
n
n
s
s
f
f
o
o
r
r
t
t
h
h
e
e
h
h
e
e
d
d
g
g
e
e
t
t
r
r
i
i
m
m
m
m
e
e
r
r
• Remove unconditionally any foreign objects out of the hedge
(e.g. wires) as these can damage the knives of the hedge
trimmer.
• Take special care when operating close to overhead cables.
• Keep hands and feet away from the cutting device when it
moves.
• If you release the throttle trigger the cutting device will after-
run for a short time
• If you release the throttle trigger the cutting device will after-
run for a short time
• Be sure that the cutting device already moves before you
start cutting.
• Do not use a blunt, broken or otherwise damaged cutting
device.
• Never get in contact with the running cutting device with
metallic fences or the ground.
• Stop the engine and allow the machine to come to a stop
when
− the cutting tool hits a foreign object,
− abnormal operating noise is noticed,
− the machine causes abnormal vibration.
⇒ Then, pull off the spark plug connector from the spark
plug and take the following actions:
− check the machine for damages,
− check for loose parts and tighten them if necessary,
− replace damaged parts by equivalent parts or have
them repaired.
• Stop the engine and pull the spark plug connector:
− to remove jammed material,
− to eliminate faults,
− for work breaks,
− before leaving the hedge trimmer.
S
S
a
a
f
f
e
e
t
t
y
y
i
i
n
n
s
s
t
t
r
r
u
u
c
c
t
t
i
i
o
o
n
n
s
s
f
f
o
o
r
r
t
t
h
h
e
e
p
p
o
o
w
w
e
e
r
r
p
p
r
r
u
u
n
n
e
e
r
r
• Persons who work with the power pruner must exhibit on
request a training certificate appropriate to the intended use
and be familiar with the use of the power pruner and
personal protective equipment.
• Only use a suited guide bar/saw chain combination as
described under “Technical data”. Incorrect combinations
increase the risk of kickbacks.
• Is the oil tank filled (chain lubrication)?
Check the oil level on a regular basis. Top up saw chain oil
without delay to prevent the saw chain from running dry.
• Is saw chain clamped correctly?
Observe the points in paragraph “Clamping saw chain”.
• Is saw chain sharpened correctly?
Use only well sharpened saw chains as edgeless saw chains
increase not only the risk of backstrokes but also charge the
motor.
• Do not use any cracked saw chains or such that have
changed their shape.
• Securely support the power pruner when switching it on and
hold it with both hands. Chain and guide bar must stand free.
• Start cutting only when the saw chain has reached the full
number of revolutions.
• Do not attempt to hit an already existing cut.
• Do not use the power pruner for lifting or moving of wood.
• Saw splintered wood with care. There is risk of injury by
wood pieces carried away.
• Operate the power pruner only with safe standing position.
• Frequently change the working position to prevent a one-
sided work position.
• Make sure that the wood is free of foreign object (nails etc).
• Be careful at the end of a sawing cut. As soon as the power
pruner leaves the wood the force of weight changes. There is
risk of accident for legs and feet.
• Remove the power pruner only with running saw chain out of
the cut.
• If the saw chain gets jammed in the wood, stop it
immediately. Use a wedge to free the guide bar.
• Never touch wire fences or the ground with the running saw
chain.
• Switch off the power pruner between the cuts when several
cuts are carried out.
• Before leaving the power pruner for work breaks bring it in a
safe condition (cover the chain guard) and put it on a place
where nobody is endangered. Secure the power pruner
against unauthorized access.
• Stop the machine and remove the spark plug connector
when
− Contacting the power pruner with soil, stones, nails or
other foreign substances
> Check immediately chain and guide bar.
− Carrying out repair work.
− Performing maintenance and cleaning work.
− Eliminating faults.
− Transport
− Clamping again the chain
− Chain change
− Leaving of machine (also for short-term interruption)
… 29 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Atika BHS 30 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Atika BHS 30 in the language / languages: English, German, Dutch, French, Italian, Swedish as an attachment in your email.

The manual is 1,62 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info