519273

Atika ASP 5.5 Manual

21
Zoom out
Zoom in
Previous page
1/72
Next page
2. Fasten the table in the top position.
3. Switch on the device and continue the splitting
operation.
¾ Never try to split two logs at once.
¾ Never try to remove or replace the log during the splitting
process.
20
L Never try to force the splitting of the log by maintaining
the pressure for several seconds. This can lead to damage to
the machine.
Position the log on the table again and repeat the splitting
phase, or put the log on one side.
How to release a jammed log?
There is a risk of knotted logs getting stuck during the
splitting process.
1. Switch machine off and disconnect the power.
2. Carefully move the stuck log backwards and forwards to
loosen it.
Never hammer on the stuck log.
Never use a saw to cut the stuck log out of the machine.
Do not enlist the aid of a second person - this is a one-
man job.
Finishing work:
¾ Bring the splitting blade to the lower position (run-in
state).
¾ Release one of the control handles.
¾ Switch the machine off and disconnect the power.
¾ Follow the care and maintenance instructions.
C
C
a
a
r
r
e
e
a
a
n
n
d
d
m
m
a
a
i
i
n
n
t
t
e
e
n
n
a
a
n
n
c
c
e
e
Remove the plug from the power socket before
starting any maintenance or cleaning work.
Wear protective gloves in order to avoid injury to the
hands.
L Observe the following in order to keep the log splitter in
good working order:
Clean the machine thoroughly after you have
finished using it.
Remove any resin remains on the machine.
Lubricate the splitting column regularly or oil it using
environmentally friendly spray oil.
Check the oil level and change the oil as necessary.
Check hydraulic hoses and hose connections
regularly for any leaks and firm fitting.
Sharpening the splitting blade
After longer operating periods, for reduced splitting
performance or slight deformation of the cutting edge, grind
the splitting blade or sharpen it with a fine file (remove burrs).
16
Sharpen wedges
How do I check the oil level?
1. The splitting
column must be in
run-in state.
2. Now remove the
dipstick.
3. Clean the dipstick
and the oil seal.
4. Replace the
dipstick fully into
the oil reservoir.
5. Now remove the
dipstick again,
and read off the
oil level.
17
Oil dip stick
If the oil level is between the two marking on the
dipstick, there is sufficient oil in the reservoir.
18
If the oil level is below the lower marking, more oil
should be added with the aid of a clean funnel.
upper marking lower marking
6. Check the oil
seal and replace
it if it is dama-
ged in any way.
7. Replace the
dipstick into the
oil reservoir.
19
… 21 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Atika ASP 5.5 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Atika ASP 5.5 in the language / languages: English, German, Dutch, Danish, French, Polish, Swedish as an attachment in your email.

The manual is 3,94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info