519822

Atika ASP 4 Manual

14
Zoom out
Zoom in
Previous page
1/70
Next page
13
2. Place a triangular wooden chock under the log, then move
the log ram forward so that it pushes the chock under the
jammed log.
3. If the log is not released, keep repeating this procedure,
using larger chocks, until the log is released.
Never use a hammer to release a jammed log, and keep
your hands away from the log.
Do not enlist the aid of a second person - this is a one-man
job.
Do not try to release the log by using a hammer, since this
may break the motor block.
Finishing work:
Before switching off the machine at the ON/OFF switch on
the electric motor, ensure that the log ram has been
allowed to return to its starting position.
Then remove the plug from the power socket.
Close the bleed screw. Fig. 4
Follow the care and maintenance instructions.
A Log ram F Electric motor
B Bleed screw G ON/OFF switch
C Piston rod H Splitting wedge
D Dipstick I Log guide plates
E Cylinder cover J Operating handles
C
C
a
a
r
r
e
e
a
a
n
n
d
d
m
m
a
a
i
i
n
n
t
t
e
e
n
n
a
a
n
n
c
c
e
e
Remove the plug from the power socket before
starting any maintenance or cleaning work.
Wear protective gloves in order to avoid injury to the
hands.
L Observe the following in order to keep the log splitter in
good working order:
Clean the machine thoroughly after you have
finished using it.
Remove any resin remains on the machine.
Oil the piston rod (Fig. 7) regularly with an
environmentally friendly spray oil.
Check the oil level and change the oil as necessary.
Sharpening the splitting wedge
After extended periods of use, or if the splitting performance
is reduced, sharpen the splitting wedge with a file (and
remove any burrs). Fig. 9
How do I check the oil level?
1. The log ram must be in its starting position.
2. Stand the log splitter on end, with the filler opening at the
top. Fig 10
A second person will be required to up-end and
hold the log splitter.
3. Unscrew the dipstick – Fig. 11. Do not drop or lose the oil
seal when removing the dipstick.
4. Clean the dipstick and the oil seal.
5. Replace the dipstick fully into the oil reservoir.
6. Now remove the dipstick again, and read off the oil level.
If the oil level is between the two marking on the
dipstick, there is sufficient oil in the reservoir.
If the oil level is below the lower marking, more oil
should be added with the aid of a clean funnel.
lower marking upper marking
Fig. 9
A
F
E
D
C
B
H
I
J
Fig. 7
Fig. 8
G
Sharpen wedge
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Atika ASP 4 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Atika ASP 4 in the language / languages: English, German, Dutch, Danish, French, Polish, Swedish as an attachment in your email.

The manual is 4,24 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info