520111

Atika AMF2300W Manual

15
Zoom out
Zoom in
Previous page
1/140
Next page
15
Reduced output
One edge of the knife has become blunt:
Turn knife so that you can use the other edge.
All knive edges have become blunt:
Replace with new set of knives (order-no. 382425).
M
M
a
a
i
i
n
n
t
t
e
e
n
n
a
a
n
n
c
c
e
e
a
a
n
n
d
d
c
c
l
l
e
e
a
a
n
n
i
i
n
n
g
g
• Each time before starting maintenance work:
− Switch off the motor and pull out the mains plug.
− Wear protective gloves to prevent injury.
The cutters will not come to a standstill immediately after
cut-off. Before starting any service work wait until all parts
are stationary.
Be sure to have removed any tools from the machine after
completion of service work.
• Generally garden shredders require little maintenance. To
maintain their efficiency and a long life, observe the fol-
lowing:
− Keep vent slits clean and free from obstructions.
− Check the locking screws (tighten where necessary).
− Clean the device after shredding.
To clean your product only use a warm moist cloth and a soft
brush.
Never use cleaning agents or solvents. Otherwise the device
may be damaged irreversibly. Plastic parts may be corroded
by chemicals.
− Do not clean the machine with running water or high-pressure
cleaners.
After each operation treat bare metal parts with an environment-
compatible biodegradable spray oil to protect them against corro-
sion.
G
G
u
u
a
a
r
r
a
a
n
n
t
t
e
e
e
e
Please observe the enclosed terms of guarantee.
O
O
p
p
e
e
r
r
a
a
t
t
i
i
o
o
n
n
a
a
l
l
f
f
a
a
u
u
l
l
t
t
s
s
Before each fault elimination:
− Switch off device.
− Wait for standstill of the garden shredder.
− Pull out mains plug.
Fault Possible cause Removal
Motor does not start.
− No power supply.
− Mains cable defective.
− Upper part of the enclosure not properly
closed (safety shut-off is activated).
Retaining basket unlocked
− (safety cut-out device of the retaining
basket has tripped)
− Check fuses.
− Have these checked (electrician).
− Close and bolt down upper part of the enclosure cor-
rectly, remove any dirt present.
− Lock the retaining basket
Motor hums,
but does not start.
− Cutters blocked.
− Capacitor faulty.
− Switch machine off, disconnect mains plug, and clean
interior of machine.
− Have machine repaired by manufacturer or approved
company.
Reduced cutting perform-
ance.
Knife edges became blunt. Turn the knife or replace it with a new set of knives.
Device starts but blocks
under slight load and cuts off
via protective motor switch.
Extension cable too long, or cross-section
too small. Socket too far from mains sup-
ply and cross-section of mains cable too
small.
Extension cable at least 1.5 mm², maximum 25 m long. If a
longer cable is used, minimum cross-section 2.5 mm².
… 15 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Atika AMF2300W at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Atika AMF2300W in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 3,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info